User manual CURTIS RCD4400

[. . . ] Upon completion of any service or repairs to this product, ask the service technician to perform safety checks. 10. ) 11. ) 12. ) 13. ) 14. ) 15. ) 16. ) 17. ) 18. ) RCD4400 1 IMPORTANT SAFETY INSTRUCTIONS 1. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or groundingAC Polarized Plug type plug. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. [. . . ] Using AC Power 1 Check if the power voltage, as shown on the type plate located on the bottom of the set, corresponds to your local AC power supply. 3 To switch off completely, unplug the power cord from the wall outlet. · Unplug the power cord from the wall outlet to protect your set during heavy thunderstorms. Top and front panels (See 1 ) 9 10 15 11 12 13 14 16 17 18 4 x 2 R20 · UM1 · D-CELLS 10 MEMORY 14 9 13 12 ST. /MO/ REPEAT PRESET -UP 9 STOP 8 BAND PLL REMOTE CONTROL SRCD4400 VOLUME - adjusts volume level. F. FWD/REW - fast winds / rewinds the tape STOP/EJECT - stops the tape; - opens the cassette compartment. 7 FUNCTION SELECTOR (CD · TAPE · RADIO) , - selects source of sound CD, TAPE or RADIO. 9 CD SEARCH , / TUNING UP , DOWN CD: - skips or searches a passage / track backwards or forward. 18 AC MAINS - inlet for power cord. 4 5 BASIC FUNCTIONS Switching power on/off: Save energy Whether you are using mains or battery supply, to avoid unnecessary energy consumption always adjust the source selector to off. General operation 1 To select your sound source adjust the source selector to CD/TAPE/RADIO . 2 Adjust the sound with the VOLUME and DBBS (Dynamic Bass Boost) controls. - the display frequency is run, until a radio station with sufficient signal strength is found. Note: To tune to a weak station, press or briefly and repeatedly until you have found optimal reception. Tuning to preset radio stations - Press PRESET-UP until the desired preset station is displayed. RADIO GENERAL INFORMATION ON RECORDING ­ For FM, pull out the telescopic antenna. Reduce its length if the signal is too strong (very close to a transmitter). ­ For AM the set is provided with a built-in antenna so the telescopic antenna is not needed. Direct the antenna by turning the whole set. RECORDING · Recording is permissible insofar as copyright or other rights of third parties are not infringed. · This deck is not suitable for recording on CHROME (IEC II) or METAL (IEC IV) type cassettes. For recording, use NORMAL type cassettes (IEC I) on which the tabs have not been broken. Altering the VOL and DBB controls will not affect the recording in progress. · At the very beginning and end of the tape, no recording will take place during the 7 seconds, when the leader tape passes the recorder heads. · To protect a tape from accidental erasure, have the tape in front of you and break out the left tab. To record over this side again, cover the tabs with a piece of adhesive tape. Insert a suitable cassette into the cassette deck and close the cassette door. [. . . ] · Always close the CD door to keep the CD compartment dust-free. · To clean the CD, wipe in a straight line from the center towards the edge using a soft, lint-free cloth. · Never write on a CD or attach any stickers to it. Erasing a program You can erase the contents of the memory by: ­ opening the CD door; ­ selecting RADIO source; ­ pressing (twice during playback or in the stop Position) X 8 9 TROUBLESHOOTING Troubleshooting If a fault occurs, first check the points listed below before taking the set for repair. If you are unable to remedy a problem by following these hints, consult your dealer or service center. SPECIFICATION SPECIFICATIONS : POWER SUPPLY RADIO FREQUENCY COVERAGE GENERAL Headphone Speakers CD PLAYER Pick up Encoding D/A : AC 230 V, 50 Hz DC 12V (UM-1 x 8) : AM 530 - 1710 kHz. [. . . ]