User manual EARLEX WDS30P

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual EARLEX WDS30P. We hope that this EARLEX WDS30P user guide will be useful to you.


EARLEX WDS30P : Download the complete user guide (212 Ko)

Manual abstract: user guide EARLEX WDS30P

Detailed instructions for use are in the User's Guide.

[. . . ] o When lifting the unit, always hold with both hands and carry by the handle. o Always switch the unit off before changing between vacuum and blower functions. Thank you for purchasing your Earlex Wet & Dry Vacuum & Blower System. This product can be used all around the home, garage, workshop and garden. Dry Mode ­ picks up all kinds of dry material such as dust, nails, broken glass, leaves, litter and wood shavings. [. . . ] The unit has two operating modes ­ continuous and power take-off mode. With the switch set in position I (continuous mode) the vacuum motor will operate when the switch is on. With the switch in position II (power take-off mode) the operation of the vacuum motor is controlled by the power tool, plugged into the socket on the unit. 6. Beware of discharged air from the outlet on the motor housing. Operate as required in either mode, dependant on the task. You can adjust the air flow by sliding the air flow adjustor forward for maximum suction, covering the hole, or backwards, opening the hole, to reduce the suction. 4 WD0370 0908:Layout 2 2/3/09 13:35 Page 5 WARNING ­ TAKE CARE, THE TANK MAY BE HEAVIER THAN YOU THINK. 1. When the tank becomes full the cleaner will make a high pitched noise and the float shut-off will activate, causing the cleaner to lose suction. Empty collection bin of all contents, making sure you are protected against any sharp objects. To remove the filter, apply pressure to the top edge on either side of the filter and pull downwards, twisting as you pull the filter off the float cage. When replacing the filter, push onto the float cage, twisting the filter to ensure it is secure. Ensure that the filter is pushed to the top of the float cage and that the filter pleats are not squashed. Replace motor housing and clip onto bin, plug in and continue as before. FLOAT SHUT-OFF The cleaner is protected by an automatic shut-off float valve when the recovery tank becomes full of liquid. This will become apparent to you as the motor will start to make a higher pitched noise. Try to keep the hose raised whilst emptying out the liquid, this will help eliminate any spills. EMPTYING THE TANK WARNING: BE CAREFUL WHEN EMPTYING THE TANK, IT MAY BE HEAVIER THAN YOU THINK. Should the cleaner overturn during use, switch the unit off immediately, return to the upright position. If collecting soapy water you will need to regularly check whether the unit requires emptying as the lather can bypass the float system and there can be a discharge of foam. Should this occur: IMPORTANT INFORMATION The float valve is a safety device, do not attempt to remove this or modify it, it is there for your safety. 5 WD0370 0908:Layout 2 2/3/09 13:35 Page 6 1. Tip away any water around the outlet on the motor housing before restarting. The cleaner can be used as a powerful blower: 1. Ensure that the hose, tank and accessories have been cleaned of any debris before operating the blower function. Protect your eyes with safety goggles when using this function and ensure that no one else is in close proximity. Uses include blowing leaves into piles and blowing dust out of difficult areas, BLOWER FUNCTION Always switch the unit off before changing between vacuum and blower functions. STORAGE 1. [. . . ] For more information about where you can drop off your waste, please contact your local authority. o o o To order any spare parts for your wet & dry vacuum, please contact the helpline on 01483 454666 (Monday ­ Friday 08. 30-17. 00 excluding bank holidays) DISPOSAL OF POWER TOOLS TROUBLESHOOTING DO NOT: o o o o The unit does not turn on? Check the unit is plugged in and switch on. Check the fuse in plug and only replace with a fuse of the same rating ­ 13 amps. If using an extension lead, please check the fuse in this lead. Use power tools rated at more than 1600W in the power take-off socket. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE EARLEX WDS30P




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual EARLEX WDS30P will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.