User manual ECHO CS-3400

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual ECHO CS-3400. We hope that this ECHO CS-3400 user guide will be useful to you.


ECHO CS-3400 : Download the complete user guide (651 Ko)

You may also download the following manuals related to this product:

   ECHO CS-3400 (832 ko)
   ECHO CS-3400 PARTS CATALOG (1042 ko)

Manual abstract: user guide ECHO CS-3400

Detailed instructions for use are in the User's Guide.

[. . . ] Pinching the saw chain along the top of the guide bar may push the guide bar rapidly back towards the operator. Either of these reactions may cause you to lose control of the saw which could result in serious personal injury. The Kick Guard device is not installed on the guide bar when you purchase your ECHO chain saw. The Kick Guard ® can be used in a majority of cutting operations, and is especially recommended for beginners, homeowners, or chain saw novices. [. . . ] Pushing the saw too hard will slow the engine and cutting will actually be more difficult. NOTE Some material may adversely affect the housings of your ECHO chain saw. (Example: Palm Tree Acid, fertilizer, etc. ) To avoid housing deterioration, carefully remove all packed saw dust around clutch and guide bar area and wash with water. Kickback WARNING DANGER Do not let the tip of the bar touch anything while the engine is running. Should the tip contact a limb or log while the chain is moving, the tip will be pushed upward with considerable force. Avoid it! 12 FELLING A TREE DIRECTION OF FALL WARNING DANGER A falling tree can seriously damage anything it may hit - a car, a house, a fence, a power line, or another tree. There are ways to make a tree fall where you want it, so first decide where that is!You will need good footing while working and you should be able to work the saw without hitting any obstacles. When the tree begins to fall you should retreat away from the direction of fall at a 45 degree angle to avoid the trunk kicking back over the stump. Hinge 45° Direction of fall 2" First cut Felling cut Notch Second cut One-third tree diameter 2" Begin the cut on the side to which the tree is to fall. The position of this notch is important since the tree will try to fall "into" the notch. The felling cut is made on the side opposite the notch and at a level about 2" above the bottom of the notch. The remaining wood between the notch cut and felling cut (about 2") will act as a hinge when the tree falls, guiding it in the desired direction. Lightly brush dust off filter, and inspect for damage. AUTOMATIC OILER B D · The discharge volume of the automatic oiler is adjusted to 3 to 4 cc/mm (@ 7000 rpm) prior to shipment from the factory. · Turn adjusting screw (D) counter-clockwise to increase oil volume, clockwise to decrease oil volume. OIL STRAINER · Check periodically. - When the inside of the tank gets dirty, rinsing the tank out with gasoline will clean it. - Clogged strainer will cause difficulty in starting engine or abnormalities in engine performance. - Pick up the fuel strainer (F) through fuel inlet port with a piece of steel wire, or the like. - When the inside of the fuel tank is dirty, rinsing the tank out with suitable cleaning fluid will clean it. E FUEL STRAINER · GUIDE BAR AND OIL HOLES · Clean after each use - Clean the grooves (G) of the guide bar with, for example, a small screwdriver. Reverse guide bar periodically. · F SPROCKET · H · G · A damaged sprocket (J) will cause premature damage or wear of saw chain. - When the sprocket has worn out 0. 5mm (. 020") or more, replace it. Thoroughly wash the guide bar and sprocket areas after each use, then coat metal parts with light oil. J 16 SPARK PLUG · · · Check periodically Gap = 0. 65mm (. 026 in. ) Replace if either electrode is worn, or if the insulator is fouled by oil or other deposits. lb. ) IMPORTANT Do not over-torque. · COOLING SYSTEM CLEANING · · · Remove spark plug lead. Use a stiff bristle cleaning brush (do not us a metal brush) to remove dirt from cylinder fins in muffler and ignition coil areas. · 17 CARBURETOR ADJUSTMENT Engine Break-In New engines must be operated a minimum duration of two tanks of fuel break-in before carburetor adjustments can be made. [. . . ] Chain saw pressed against tree to firmly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Replace. Chain stops (Clutch slips) No oil in tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chain poorly lubricated Oil contaminated with dust . . . . . . . . . . . . . . . . . . . . . . . . . . . . Use oil with correct viscosity for summer or winter. STORAGE · Inspect and adjust every part of the chain saw. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE ECHO CS-3400




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ECHO CS-3400 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.