User manual EDIROL CG-8

[. . . ] 201b Before using this unit, carefully read the sections entitled: "IMPORTANT SAFETY INSTRUCTIONS" (p. These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, OWNER'S MANUAL should be read in its entirety. The manual should be saved and kept on hand as a convenient reference. 202 Copyright © 2005 ROLAND CORPORATION All rights reserved. [. . . ] If you want to use a project that's stored on a CompactFlash card, you must first copy it into the CG-8's internal hard disk, and then assign it to a visual pad. For details on how to copy a project, refer to "Managing projects and pictures" (p. :Project :Folder 6 Use the [ button. PREV][NEXT ] buttons to select "ASSIGN, " and press the [ENTER] You will return to the PROJECT EDITOR screen. The project you selected in step 5 will be assigned to the visual pad you selected in step 3. If in step 3 you select a visual pad to which a project is already assigned, the project assignment for that pad will be overwritten. (This only changes the assignment for that visual pad; the project itself will not be overwritten. ) 55 About projects Deleting a project assignment for a visual pad 1. Follow steps 1­2 of "Assigning a project to a visual pad" (p. Turn the [VALUE] dial to move the guide, and select the project whose pad assignment you want to delete. Use the [ PREV][NEXT ] buttons to choose "CLEAR ASSIGNMENT, " and press the [ENTER] button. Are you sure?" Use the [ PREV][NEXT ] buttons to choose "OK, " and press the [ENTER] button. If you decide not to delete the assignment, choose "CANCEL" and press the [ENTER] button. The visual pad you selected in step 3 will indicate "---. " In the screen, project names will be shown in locations corresponding to the visual pads to which a project has already been assigned. If no project has been assigned, this area will indicate "---. " 4. This operation only deletes the assignment from the visual pad; it does not delete the project itself. For details on how to actually delete a project, refer to "Managing projects and pictures" (p. 84). 56 About projects Editing a project This section explains how to load the pictures (Photo Pictures and Stamp Pictures) you want to use in a project. From the internal hard disk or a CompactFlash card via the included card adaptor, you need to separately load the image files you want to use as Photo Pictures and Stamp Pictures, and assign them to the visual pads. Images that you can use as a Photo Picture or Stamp Picture Image files that you created on your computer or captured using a digital camera can be used as Photo Pictures and Stamp Pictures. When you load an image into a project, Photo Pictures (JPEG files) will be automatically resized to 512 x 384 pixels, and Stamp Pictures (PNG files) will be automatically resized to 512 x 256 pixels. Photo Pictures · Format: JPEG file (. jpg) · Size: 3000 x 2000 pixels or smaller Stamp Pictures · Format: PNG file (. png) · Size: 3000 x 2000 pixels or smaller Assigning a Photo Picture or Stamp Picture to a visual pad 1 Press and hold the [MENU] button for two seconds or longer to access the MAIN MENU screen. Don't insert or remove a CompactFlash card while a menu screen is shown (i. e. , in Menu mode). Doing so may damage the data on the CompactFlash card. fig. main-menu01. eps 57 About projects 2 Use the [ PREV][NEXT [ENTER] button. ] buttons to select "PROJECT EDITOR" and press the In the screen, project names will be shown in locations corresponding to the visual pads to which a project has already been assigned. If no project has been assigned, this area will indicate "---. " The PROJECT EDITOR screen will appear. fig. project-menu01. e. eps To return to the MAIN MENU screen, press the [EXIT] button. Alternatively, you can press the [MENU] button to return to Play mode. Guide 3 4 Turn the VALUE dial to move the guide, and select the project into which you want to load a Photo Picture or Stamp Picture. ] buttons to select "EDIT PROJECT, " and press the You can't select a project that is not assigned to a visual pad (p. 54). The EDIT PROJECT screen will appear. fig. material-assign01. e. eps If in step 3 you select a visual pad to which no project is assigned (displayed as "---"), the message "No project assigned" will appear. [. . . ] ­ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ­ Consult the dealer or an experienced radio/TV technician for help. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Unauthorized changes or modification to this system can void the users authority to operate this equipment. [. . . ]