User manual EDIROL R-4 PRO

[. . . ] For EU Countries CAUTION Apparatus containing Lithium batteries Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer's instructions. ADVARSEL! Lithiumbatteri - Eksplosionsfare ved fejlagtig håndtering. Levér det brugte batteri tilbage til leverandøren. VARNING Explosionsfara vid felaktigt batteribyte. [. . . ] * Effects are not available when the R-4 Pro is operating at 96 kHz. Effect types provided on the R-4 Pro No. 0 1 2 3 4 Effect name No Effect 3-Band EQ Graphic EQ Noise Gate Enhancer Effect No effects are applied. Use this setting if you want to preserve the effect on/off setting of each channel but do not want an effect to be applied. This effect minimizes the noise that might be heard in silent regions as well as low-frequency noise. By adding a phase-shifted sound to the direct sound, this effect sharpens the definition of the sound and pushes it toward the foreground. This cuts the sibilance that can be obtrusive in a vocal, making the sound smoother. It also reduces the difference between loud and soft sounds, making the level more consistent. A compressor evens out the level differences between loud and soft sounds. A de-esser reduces the unpleasant sibilance (exaggerated "s" sound) that is sometimes present in a vocal. Converting sound recorded on a MS (Mid-Side type) mic to stereo. 5 Comp&DeEsser 6 MS-Mic If you apply an effect while recording, the volume and tone of the recorded sound will be different than the original sound. Before applying an effect aggressively during recording, it is a good idea to monitor the sound through headphones in recording standby mode to make sure that the sound is not clipped or distorted. It is also a good idea to make a test recording beforehand with those settings. For details on the procedure, refer to "Effects settings" (p. If the [EFFECT] button is pressed during recording or playback, the effect is toggled on/off. To prevent unintentionally switching an effect on or off, we recommend turning the HOLD switch on. What is an effect?On the R-4 Pro, an "effect" is a process that digitally transforms the sound, giving it greater clarity or impact. Effects can also make the sound more intelligible or reduce undesirable noise. Applying an effect or boosting the level may increase the sound level (volume) beyond the maximum that a device can handle; this occurrence is called clipping. The MS mic The MS mic creates stereo sound by combining sound from a main mic that records central sounds (midsignal: M) and a bi-directional mic that records lateral sounds (side signal: S). 59 Effects settings Applying effects You can adjust the R-4 Pro effects not only while standing-by for recording or playback, but also while you listen to the sound during actual playback or recording. This section explains how to adjust the effect settings while playing back or in recording standby mode. fig. effect-set. eps 1 3 6 fig. effect-1. eps 2 1 Press the R-4 Pro [EFFECTS] button. The Effects setup screen is shown in the display. fig. effect-type. eps 2 Use the [SCRUB/VALUE] dial to select the desired effect type. For details on each effect type, see to "Effects" (p. The cursor will move to the "Link" field. CH1 CH2 CH3 CH4 CH1+2 CH3+4 CH1+2+3+4 The effect on/off setting and effect parameters are set independently for each channel. The effect on/off setting and effect parameters are linked for channels 1 and 2 and for channels 3 and 4. [. . . ] 11 Sample size W . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wave edit button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . wav WAVE EDIT 23 11 11 83 X XLR input connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IMPORTANT: THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE. [. . . ]