User manual ELICA TWIN

[. . . ] 14 EN - Instruction on mounting and use Consult the designs in the front pages referenced in the text by alphabet letters. All responsibility, for any eventual inconveniences, damages or fires caused by not complying with the instructions in this manual, is declined. Note: the elements marked with the symbol “(*)” are optional accessories supplied only with some models or elements to purchase, not supplied. Do not connect the appliance to the mains until the installation is fully complete. [. . . ] It is recommended that the cooker hood suction is switched on for 5 minutes prior to cooking and to leave in operation during cooking and for another 15 minutes approximately after terminating cooking. The hood is equipped with a “TOUCH” device to control the lights and speed. The cooker hood can be controlled through a remote control available as accessory kit (see the paragraph relating to the functioning of the remote control). Automatic start-up function The hood is equipped with a temperature sensor which activates the motor to the first suction speed (power) in the event that the room temperature in the surrounding area is higher than 70°C. 16 First proceed with filter maintenance as described in corresponding paragraph. Press and hold down (for more than 3 seconds) the T1 button on the control panel, the LED light will stop flashing indicating that the signal reset has been carried out, the hood will switch off. reset coal filter saturation signal (FLASHING ORANGE (amber) LED light) First proceed with filter maintenance as described in corresponding paragraph. Press and hold down (for more than 3 seconds) the T1 button on the control panel, the LED light will stop flashing indicating that the signal reset has been carried out, the hood will switch off. Coal filter saturation signal disactivaction (for particular applications) Switch off hood (see above paragraph “suction speed (power) selection”). Press and hold down (for more than 5 seconds) the T1 button on the control panel, the LED light will start flashing GREEN indicating that the coal filter saturation signal has been disactivated. In order to reactivate the coal filter saturation signal, repeat operation, the LED light will flash ORANGE (amber) The central light can be switched on and off in two ways: 1. Press the “+” key or the “-” key respectively to switch the central light (ON) or (OFF). Press the "■" key to change the state of the light from (OFF) to (ON) or vice versa. Controlling the lateral lights: Press the "◄" key or the "►" key until seeing the symbol relating to the “Controlling the lateral lights” function on the remote control. Press the "■" key to change the state of the lateral lights from (OFF) to (ON) at maximum intensity and viceversa. Press the “-” key to diminish the intensity of the lateral lights until switching them off. Press the “+” key to increase the intensity of the lateral lights. Resetting and configuring the saturation of the filters signal Switch the hood on at any speed (see paragraph above “Selecting the suction speed (power”). Press the "◄" key or the "►" key until seeing the symbol relating to the “Resetting and configuration of the saturation of the filters signal” function on the remote control. Resetting the anti-fat filter saturation signal (GREEN LED FLASHING on the control bar) First proceed with the maintenance of the filter as described in the corresponding paragraph. Press the “+” and “-” keys contemporaneously for about 3 seconds. The LED stops flashing, indicating that the resetting of the signal has been accomplished. [. . . ] Reset og konfigurasjon av signaleringen for skitne filtre Slå på ventilatorhetten i en hvilken som helst hastighet (se avsnittet ovenfor: “Valg av sugehastighet (styrke)”) Trykk på knappen "◄" eller "►" helt til du ser funksjonssymbolet “Reset og konfigurasjon av signaleringen for skitne filtre” på fjernkontrollen. For å aktivere signaleringen må du følge instruksjonene i avsnittet: “Aktivering av signaleringen for skittent karbonfilter”. Deaktivering av signaleringen for skittent karbonfilter (for spesielle anvendelser) Slå av ventilatorhetten (se avsnittet ovenfor: “Valg av sugehastighet (styrke)”) Trykk på knappen “"◄" eller "►" helt til du ser funksjonssymbolet “Reset og konfigurasjon av signaleringen for skitne filtre” på fjernkontrollen. For å gjenaktivere signaleringen for skittent karbonfilter, repeteres denne prosedyren, og LED-lampen vil blinke ORANSJE. [. . . ]