User manual FUJIFILM EXIF VIEWER QUICK START

[. . . ] I I I I USB Mass Storage Driver Exif Viewer DP Editor Exif Launcher Quick Start Guide Thank you for purchasing these FUJIFILM products. This Quick Start Guide provides you with a simple summary of how connect your PC and camera via the USB ports and how to install the software provided in this package on your personal computer (PC). Read this guide carefully to ensure that you use the software correctly. For detailed information on how to use the Exif Viewer and DP Editor software, refer to the User's Guide on the enclosed CD-ROM. BB10768-301(1) E IMPORTANT Be sure to read this page before using the Software. 6. [. . . ] Start up your PC and double-click the "My Computer" icon. 2. Load a media containing photographed images into your camera, switch the camera on and set the Mode dial to "Playback" mode. NOTE The media used should contain images shot using a FUJIFILM camera. Using the User's Guide 1. When you open the Manual folder in the Viewer folder on the CD-ROM, it contains the following file. English. pdf: User's Guide For easier viewing, copy the English. pdf file onto the hard disk in your PC. For information on how to use Acrobat Reader, refer to the online guide provided in the Acrobat Reader Help menu. 3. When the "Removable Drive" icon appears in the "My Computer" window, the camera and PC are correctly connected. 16 17 Windows If Exif Viewer and Exif Launcher are installed, Exif Viewer starts up and the window shown here appears. TIP · When you install Exif Launcher, it is registered in the startup menu and is launched automatically when Windows starts up. To quit Exif Launcher, click the right mouse button on the [ ] icon in the taskbar and select "Exit" from the Thumbnail display area menu that appears. · If Exif Launcher does not run, the Exif Viewer will not start up. If the icon in the figure is shown in the taskbar, Exif Launcher is running. 6. To exit Exif Viewer, select "Exit" from the "File" menu or click the [Close] button in the main window. For more information on using Exif Viewer or DP Editor, refer to the User's Guide (PDF document) on the CD-ROM. 7. Check that the camera display indicates that data access is no longer in progress. On Windows 2000 Professional, click the eject icon [ ] on the taskbar when the camera display indicates that data access is no longer in progress and remove "USB Mass Storage". Disconnect the USB cable and remove the SmartMedia. NOTE · Always check that all camera files are closed and that the camera display indicates that data access is no longer in progress. Do not disconnect the USB cable or remove the SmartMedia immediately after the "Copying" message has gone off. If a large amount of data is being copied, camera access continues for a short time after the message displayed on the PC has gone off. · Refer to the camera Owner's Manual for more information on the access display on the camera. · In Windows 2000 Professional, disconnecting the USB cable without performing the "Unplug or Eject hardware" procedure can cause the computer to hang. 4. Thumbnail images for the image data recorded on the SmartMedia are displayed in the thumbnail display area. If you double-click a thumbnail image, the image is displayed in an Image window. To close the image window, use the [Close] button in the top right corner of the window. You can also copy the image to your PC desktop by dragging the thumbnail from the thumbnail display area and dropping it onto the desktop. NOTE Do not perform the operations listed below when a camera file is open and the camera display indicates that data access is in progress. [. . . ] Solution: For Windows 98 or Windows Me, specify \USBDRV\WIN98\USBS04CB. INF. INF. When I connect the camera to my PC, the "Add New Hardware Wizard" appears. I Is the USB Driver installed?Solution: Install the USB Driver software as directed by the on-screen instructions. When I double-click the removable disk icon, "The device is not ready" error message appears. I Is the media loaded in the camera?Refer to the Owner's Manual supplied with the camera for details. A warning message appeared when I removed the media from the camera. Solution: This procedure may corrupt the data on the media or damage the media itself. [. . . ]