User manual FUNAI FE226G

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The caution marking is located on the rear of the cabinet. IMPORTANT SAFEGUARDS 1. Read instructions-All the safety and operating instructions should be read before the appliance is operated. 2. Retain Instructions-The safety and operating instructions should be retained for future reference. 3. Heed Warnings-All warnings on the appliance and in the operating instructions should be adhered to. 4. Follow Instructions-All operating and use instructions should be followed. [. . . ] Unsuitable for children under 13 Restricted; under 17 requires accompanying parent or adult guardian No one under 17 admitted Mature audience only Press the number buttons to enter your desired access code in the NEW CODE space. · If you enter wrong code, repeat step 4, making sure you enter the same new code exactly in the confirm code space. CONFIRM CODE ____ 5 Exit the V-Chip setting mode Press SETUP on the remote control to return to original mode. NOTE: · If you unplug the power cord or power failure occurs, the changed access code will be lost and will return to default (0000). Change your access code again as necessary. · When you select the rating category and turn it · [BLOCK], the higher rating will turn [BLOCK] automatically. When you turn "G" to [VIEW], all ratings will turn to [VIEW] automatically. Exit the V-Chip setting mode 5 Press SETUP on the remote control to return to original mode. ­ 18 ­ EN 0C28 DVD SECTION ABOUT THE DISCS PLAYABLE DISCS The following discs can be played back on this TV/DVD. ¡DVD video ¡DVD+R/RW* ¡CD-R/RW* ¡DVD-R/RW* ¡Audio CD ¡MP3* DISC TYPES [DVD] Data on a DVD is divided into sections called "titles" and then into subsections called "chapters", each of which is given a title or chapter number. Playback conditions are preset on some DVD video discs and these playback conditions take priority over user operations on this TV/DVD. If a function you selected does not run as desired, refer to the manual accompanying the disc. * Depending on the types or the writing method of the medium some discs can not be played. · Some DVD-R/RW, DVD+R/RW, or CD-R/RW discs made on personal computers or on DVD recorders may not be played back properly due to the factors such as scratches, dirt or special properties of the disc. · Discs made on personal computers may not be played back properly due to the different environment or the settings of the application you use. You cannot play discs recorded in other color systems such as PAL or SECAM. ¡Some discs include region codes as shown below. Example Title 1 Title 2 Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1 Chapter 2 [AUDIO CD] Data on an audio CD is divided into sections called "tracks", each of which is given a track number. Example Track 1 Track 2 Track 3 Track 4 Track 5 Track 6 ¡The number inside the symbol refers to a region of the world, and a disc encoded in a specific region format can only be played back on TV/DVD with the same region code. 2 Press FWD g or REV h. ¡" STEP BY STEP PLAYBACK DVD-V 1 During playback, press PAUSE. ¡Playback will pause and sound will be muted. 1" or " 1" appears on the screen. 3 To select another speed, repeat step2 until your required speed appears on the screen. ¡Slow forward or reverse speed varies with the disc. 2 The disc goes forward by one frame each time PAUSE is pressed. Approximate speed is 1(1/16), 2(1/8) and 3(1/2). ¡When you use buttons on the TV/DVD front panel, 3 To exit step by step playback, press PLAY. press and hold NEXT G /SEARCH g or PREV H /SEARCH h for a few seconds. 4 To return to normal playback, press PLAY. ­ 21 ­ EN 0C28 SEARCH FUNCTION TRACK SEARCH CD MP3 TIME SEARCH DVD-V CD There are three ways to begin playback on an Audio CD and MP3 at a specific track. Using the number buttons on the remote control 1 During playback press SEARCH MODE three times (CD: twice) to display the Time Search on the TV screen. 1 Press the number buttons to enter the desired track number. ¡For single digit tracks (1-9), press a single number 2 Within 30 seconds, enter a desired disc time using the number buttons. track 3, press 3). ¡To play track 26, press +10, 2, 6. appears automatically. For example, " 0 : 0 - : - -" appears in the Time Search display if the total time of the disc is less than 10 minutes. Using SEARCH MODE 1 Press SEARCH MODE. ¡The Track search display appears. MARKER SETUP SCREEN DVD-V CD 2 Within 30 seconds, select a desired track number using the number buttons. ¡Playback will start at the selected track. Use markers to memorise your favorite places on a disc. 1 Press SEARCH MODE four times (CD: three times) during playback. ¡The display screen and Markers will appear on the Using PREV/NEXT (H/G) During playback, press NEXT G to move the next track. ¡If NEXT G is pressed while the playback is paused, the playback will be paused again after skipping to the next track. NOTE ¡PREV/NEXT (H/G) are not available when playback is stopped. TV screen. 2 Press Arrow (s/ B) to select 1, 2, 3, 4, 5, 6, 7, 8, 9, or 10 and ensure that "- - - - : - - : - -" appears in the display. 3 When you reach the desired point press ENTER. ¡The title or track and elapsed playing time will appear on the TV screen. 4 To return to the Marker later, press SEARCH TITLE / CHAPTER SEARCH DVD-V 1 Press SEARCH MODE once for the Chapter search and twice for the Title search during playback. _/2 MODE four times (CD: three times) during playback and Arrow (s/ B) to choose the desired marker then press ENTER. NOTES ¡Opening the disc tray or turning off the power or 2 Enter the desired chapter/title number using the number buttons. [. . . ] 1 Pulse el boton POWER. ¡La alimentación se conectará. 1 Seleccione "AJUSTE DE CANAL" ­MENU­ B AJUSTE DE CANAL AJUSTE DE V-CHIP IDIOMA [ESPAÑOL]` TITULO [OFF] Pulse el botón SETUP en el mando a distancia. Pulse el botón K o L para señalar "AJUSTE DE CANAL". A continuación, pulse el botón ENTER. 2 Pulse el botón OPEN/CLOSE. ¡La bandeja de carga del disco se abrirá. 3 Ponga el dlsco en la bandeja con el lado de la eliguta hacia arriba. ­ AJUSTE DE CANAL ­ 2 Empiece el prefijado automático AGREGAR/BORRAR (CATV) Pulse el botón K o L para señalar "AUTOPROGRAMACION DE CA". El sintonizador busca y memoriza todos los canales activos en su localidad. B AUTOPROGRAMACION DE CA. 3 Después de buscar 4 Pulse el botón PLAY. [. . . ]