User manual FUNAI TD6D-D4413DB.PDF

[. . . ] button on the VCR for 3 sec· When a picture does not appear on the TV screen, repeat step [4]. 5) Press the STOP button to stop playback. Owner's Manual Video Cassette Recorder If you need additional operating assistance after reading this owner's manual or to order replacement accessories, please call TOLL FREE : 1-800-256-2487 or visit our web site at http://www. funai-corp. com TD6D-D4413DB. PDF Basic VCR/TV Connection Cable Signal or Antenna (Back of TV) Cable Signal or 1. Before using your VCR Antenna (Back of VCR) (Back of TV) ANT IN Stereo TV Connection You can use the AUDIO OUT jacks and VIDEO OUT jack on the back of the VCR if your TV has Audio/Video Input jacks. Please refer to your TV's owner's manual. VIDEO IN AUDIO IN L R AUDIO L OUT R VIDEO IN ANT IN OUT OUT IN Audio/Video Cables (not supplied) ANT IN VIDEO OUT AUDIO OUT Disconnect 2 Connect OUT 3 Connect (supplied) L R (Back of TV) Connect 1 OUT (Back of VCR) RF Cable Front & Rear Terminals AUDIO OUT jacks Connect the audio cables to the audio in jacks of a camcorder, another VCR, a stereo amplifier, or an audio system. AUDIO L AUDIO L ANT IN 4 Plug the AC power cords of the VCR and TV into the AC outlets. Hint for Cable Box or Satellite Box Connection A Cable Signal (Cable box or Satellite box) IN OUT AUDIO IN jacks Connect the audio cables from the audio out jacks of a camcorder, another VCR, or an audio source. ANT IN OUT R IN (Back of VCR) ANT IN Connection B ANT IN (Back of VCR) OUT OUT RF Cable (supplied) E Cable Signal (Cable box or Satellite box) IN OUT ANT IN jack Connect your antenna or cable box. [. . . ] Notes for using the Number buttons: · When selecting cable channels which are higher than 99, enter channel numbers as a three-digit number. (For example: 117, press 1, 1, 7) · You must precede single-digit channel numbers with a zero (For example: 02, 03, 04 and so on). 1 MENU -MENUTIMER PROGRAMMING AUTO REPEAT [OFF] B CHANNEL SET UP CLOCK SET LANGUAGE SELECT AUDIO OUT TV STEREO [ON] SAP 1 MENU -MENUTIMER PROGRAMMING AUTO REPEAT [OFF] CHANNEL SET UP B CLOCK SET LANGUAGE SELECT AUDIO OUT TV STEREO [ON] SAP 5 STOP PLAY CLOCK SET MONTH DAY YEAR 0 3 / 1 5 MON 2 0 0 4 HOUR MINUTE 05 : ­­ AM/PM ­­ or STOP PLAY STOP PLAY or or 2 POWER Remote Control TV Screen F. FWD LANGUAGE SELECT B ENGLISH STOP PLAY · If the clock is not set, the CLOCK SET screen appears when you press the MENU button. Finally, press the C. RESET/EXIT button. Select "ADD" or "DELETE" Select the current year F. FWD Hint · Repeat these steps only if there was a power failure or if the VCR has been unplugged for more than 30 seconds. 5 To exit the menu. Precautions Precautions Install Location For safety and optimum performance of your VCR: · Install the VCR in a horizontal and stable position. · Shield it from direct sunlight and keep it away from sources of intense heat. Avoid places with insufficient ventilation for proper heat dissipation. Avoid locations subject to strong vibration or strong magnetic fields. Important Copyright Information Unauthorized recording or use of broadcast television programming, video tape, film or other copyrighted material may violate applicable copyright laws. We assume no responsibility for the unauthorized duplication, use, or other acts which infringe upon the rights of copyright owners. Troubleshooting Guide If you are having problems operating your product even though you have followed the instructions in this manual, check the following list of problems and corrective actions. Timer recording is impossible. CORRECTIVE ACTION · Make sure the power plug is connected to an AC outlet. If needed, cover the hole with cellophane tape. A Note about Recycling This product's packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your local recycling regulations. Each time you press the button, the picture will be forwarded by one frame. · If the picture begins to vibrate vertically during the still mode, stabilize the picture by pressing the CHANNEL buttons. · If the picture is distorted or rolling vertically, adjust the vertical hold control on your TV, if equipped. To temporarily stop recording (Pause mode) Press the PAUSE/STILL button. · During the rec pause mode, five C marks appear on the TV screen. · Press it again to resume recording. REW STOP PLAY F. FWD 3 STOP 4 EJECT STOP 3 Hint EJECT A 2 3 4 2 · When a tape without record tab is inserted, the VCR will start playback automatically at step [1]. To adjust the tracking manually, press the CHANNEL buttons. Auto Rewind When a tape reaches its end during playback, fast-forward, or recording (except timer recording and One Touch Recording), the tape will automatically rewind to the beginning. After rewinding finishes, the VCR will eject the tape and turn itself to off. Counter Reset Press the C. RESET/EXIT button. 6. Recording & OTR (One Touch Recording) Before: Turn on the TV and set it to channel 3. · If channel 3 is already occupied for broadcasting, see "RF Output Channel" section. Hint 2 6 EJECT VCR /TV 2 POWER 1 4 · Still/Slow/Pause mode will be automatically cancelled after 5 minutes to prevent damage to the tape and the video head. · To return to playback from the Picture Search/Still/Slow mode, press the PLAY button. 1 with tab 2 1 4 7 2 5 8 0 Remote Control TV Screen 8. On-Screen Operations 1 R CHANNEL MENU REC/OTR 1 4 2 5 8 0 SPEED 3 6 9 SLOW CHANNEL 3 6 9 CHANNEL To call up the main menu MENU CH12 7 MENU SEARCH -MODE C. RESET EXIT T P/EJEC STO REW PLAY F. FWD -MENUB TIMER PROGRAMMING AUTO REPEAT [OFF] CHANNEL SET UP CLOCK SET LANGUAGE SELECT POWER VCR/TV TAPE IN TIMER REC POWER VCR/TV TAPE IN · Select the desired channel · Select the desired tape speed Recording/Playback Time T60 1hour 3hour T120 2hours 6hour T160 2-2/3hours 8hour POWER VCR/TV TAPE IN TIMER REC 3 SPEED SP Tape Speed Type of tape SP mode SLP mode 4 3 5 REC/OTR DISPLAY PAUSE /STILL REW STOP PLAY F. FWD 5 6 MENU REC/OTR STO T P/EJEC REW PLAY F. FWD 2 STOP To select an item PLAY -MENUTIMER PROGRAMMING AUTO REPEAT [OFF] B CHANNEL SET UP CLOCK SET LANGUAGE SELECT or 4 REC/OTR Accidental erasure prevention REC REC 1 4 23 You can select a fixed recording time by pressing the REC/OTR button repeatedly. REC (Normal recording) OTR(8:00) OTR(0:30) OTR(1:00). . . . . OTR(7:30) To prevent accidental recording on a recorded cassette, remove its record tab. [. . . ] This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced or missing. This EMERSON Limited warranty applies only to product purchased and used in the United States. This warranty only covers failures due to defects in material or workmanship, which occur during normal use. It does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations, or parts not supplied by FUNAI CORPORATION, or damage which results from accident, misuse, abuse, mishandling, misapplication, alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this product, or damage which results from fire, flood, lightning or other acts of God. [. . . ]