User manual GAI-TRONICS ITR1000-001

[. . . ] 43004-032B GAI-TRONICS® CORPORATION A HUBBELL COMPANY Model ITR1000-001 Basic Tone Remote Desk Set with Line Select User and Installation Manual GAI-Tronics Corporation 400 E. Mohnton, PA 19540 USA 610-777-1374 800-492-1212 Fax: 610-796-5954 VISIT WWW. GAI-TRONICS. COM FOR PRODUCT LITERATURE AND MANUALS CONFIDENTIALITY NOTICE This manual is provided solely as an operational, installation, and maintenance guide and contains sensitive business and technical information that is confidential and proprietary to GAI-Tronics. GAI-Tronics retains all intellectual property and other rights in or to the information contained herein, and such information may only be used in connection with the operation of your GAI-Tronics product or system. This manual may not be disclosed in any form, in whole or in part, directly or indirectly, to any third party. [. . . ] Always allow a short delay before speaking to allow time for the radio channel to be established. The TRANSMIT button or handset PTT bar must be held down while talking to the radio user and released to listen. When the transmission is completed, the TRANSMIT LED extinguishes and the desk set returns to the receive mode. Receiving Calls When power is applied, the desk set is in the receive mode, allowing receive audio to be heard through the speaker or handset. The desk set is always in receive mode unless the user presses the TRANSMIT or IC buttons. The desk set contains an internal or local speaker and a handset speaker, which operate as follows: · · When the handset is in the cradle or on-hook, receive audio is heard on the local internal speaker. When the handset is off-hook, receive audio is routed to the handset. Handset Transmit Using the handset is recommended when the desk set is located in noisy surroundings. Press the handset PTT bar or TRANSMIT button and speak into the handset microphone. Transmit From Internal Microphone Use the internal microphone only in low noise environments. Press the TRANSMIT button and speak in the direction of the internal microphone. For the best transmit audio quality, maintain a distance of about 12 to 18 inches from the microphone. 11/10 10 Installation Planning the Installation Sample ITR1000-001 Installation Diagram - Shown connected in parallel within one building. Mechanical Receipt Inspection The ITR1000-001 Basic Tone Remote Desk Set is shipped in a cardboard container with inserts. In-transit damage should be immediately reported to the transportation company. Mounting The desk set can be placed on a desk or mounted vertically on a wall. To wall mount the desk set, remove the four bottom screws from the base and then rotate the base 180°. Reinstall the four screws to the base and rotate the handset hook located on the front of the unit. FCC Interference Warnings The FCC requires that manuals pertaining to Class A and Class B computing devices contain warnings about possible interference with local and residential radio and TV reception. Please read these warnings and all safety information in the Foreword section of this manual. 11 11/10 Installation ITR1000-001 Basic Tone Remote Desk Set Equipment Required Test Equipment · · · · RF service monitor AC voltmeter with dB ranges for measuring audio levels #1 Phillips screwdriver 1/8-inch flat blade screwdriver Documentation · · base station's tone remote adapter manual these installation instructions Cable Installation Safety Considerations Interconnecting, communications, and Class 2 dc power cables should be separated from electrical light or other Class 1 circuits by at least 2 inches. The exception is where Class 1 wiring or power circuits are run in a raceway, or are metal-sheathed or metal-clad, or are permanently separately from the conductors of the other circuitry by a continuous and firmly fixed nonconductor such as porcelain tubes or flexible tubing in addition to the insulation on the wire. Communications cables and in-building wiring should be listed and marked for the purpose according to NEC Article 800. Telephone Line Lightning and Over-voltage Protection The ITR1000-001 Basic Tone Remote Desk Set has an over-current phone line fuse (F2) which protects against occasional extreme fault conditions that may get past the primary protectors. If the fuse requires replacement, replace F2 only with the same type Bussmann C515S 1. 25A fuse. For maximum surge and lightning protection, building primary (over-voltage) protectors should be installed at the point where the telephone lines enter the radio equipment building. Primary protectors are usually required by local codes and should be provided by your leased line provider. Power Connections Power is applied to the ITR1000-001 from the provided ac wall transformer that is supplied with the unit. Power is applied to TS1-6 (+, lead with white dashed stripe) and TS1-5 (-). 11/10 12 ITR1000-001 Basic Tone Remote Desk Set Installation Line Connections To make the required line connections, a cable with a tinned bare leads stripped to about 3/8-inch or pin terminal is necessary. With the housing opened, route the lines through the slot in the housing bottom. Using a small slotted screwdriver, connect the Line 1 two-wire line to the TS1 terminal block on the main circuit board at terminal positions 3 and 4. Connect the Line 2 two-wire line to the TS1 terminal block at positions 1 and 2. [. . . ] Refer to the tone adapter service manual for valid function tones that will key the radio. Ensure that the desk set output level is set properly, and that the HLGT is set in a range of 0 dBm to -10 dBm into the telephone line. Assuming no more than 20 dB of line loss on the telephone line, this level should be adequate for the tone adapter to decode the tone sequence. RX audio is low or distorted. Ensure that the tone remote adapter is wired correctly, including the RX audio pair. Audio quality is limited by the quality of the private radio circuit or leased lines between the station radio equipment and the remote dispatch point(s). [. . . ]