User manual GARMIN G1000 NON-AIRFRAMESPECIFIC TRANSPONDER PILOTS GUIDE
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual GARMIN G1000 NON-AIRFRAMESPECIFIC TRANSPONDER PILOTS GUIDE. We hope that this GARMIN G1000 NON-AIRFRAMESPECIFIC TRANSPONDER PILOTS GUIDE user guide will be useful to you.
Manual abstract: user guide GARMIN G1000 NON-AIRFRAMESPECIFIC TRANSPONDER PILOTS GUIDE
Detailed instructions for use are in the User's Guide.
[. . . ] This pilot's guide provides a description of the transponder operation and information on Mode S capability. The transponder controls are located on the G1000 Primary Flight Display (PFD) on the lower portion of the screen (see figures below).
When the CODE softkey is pressed, the number softkeys appear in the softkey bar (Figure 5. 1. 3): 0, 1, 2, 3, 4, 5, 6, 7, IDENT, BKSP, BACK. [. . . ] For aircraft not equipped with TCAS or TAS, TIS provides a graphic display of traffic information. TIS displays up to eight (8) traffic targets within 7. 5 nautical miles from 3, 000 feet below to 3, 500 feet above your aircraft. TIS data is updated approximately once every five (5) seconds.
NOTE: TIS is intended only to assist in visual acquisition of other aircraft in Visual Meteorological Conditions (VMC). NOTE: Aircraft without an operating transponder are invisible to TIS.
5-2
Garmin G1000 Transponder Pilot's Guide
190-00382-00 Rev. D
OPERATION
5. 2 OPERATION
MODE SELECTION
Mode selection can be automatic (Ground and Altitude modes) or manual (Standby, ON and Altitude modes). The STBY, ON and ALT softkeys can be accessed by pressing the XPDR softkey.
Standby Mode (Manual)
The Standby mode can be selected at any time by pressing the STBY softkey. In Standby mode, the transponder does not reply to interrogations, but new codes can be entered. If the Standby mode is selected, a white STBY indication appears in the mode field of the Transponder Status bar.
Ground Mode (Automatic)
Ground mode is automatically selected when the aircraft is on the ground. A green GND indication appears in the mode field of the Transponder Status bar. In Ground mode, the transponder does not allow Mode A and Mode C replies, but it does permit acquisition squitter and replies to discretely addressed Mode S interrogations.
Figure 5. 2. 2 Standby Mode
NOTE: In Standby mode, the IDENT function is inhibited.
Manual ON Mode
The ON mode can be selected at any time by pressing the ON softkey. ON mode generates Mode A and Mode S replies, but Mode C altitude reporting is inhibited. In ON mode, a green ON indication appears in the mode field of the Transponder Status bar.
Figure 5. 2. 1 Ground Mode
NOTE: Ground mode can be overridden by pressing any one of the Mode Selection softkeys.
Figure 5. 2. 3 ON Mode
190-00382-00 Rev. [. . . ] · 0000 Code for military use in the U. S.
Figure 5. 2. 7 IDENT Indication
When the IDENT softkey is pressed while in Mode or Code Selection, the system reverts to the Top-level softkeys.
NOTE: In Standby mode, the IDENT softkey is inoperative.
190-00382-00 Rev. D
Garmin G1000 Transponder Pilot's Guide
5-5
Garmin International, Inc. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE GARMIN G1000 NON-AIRFRAMESPECIFIC TRANSPONDER PILOTS GUIDE
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual GARMIN G1000 NON-AIRFRAMESPECIFIC TRANSPONDER PILOTS GUIDE will begin.