Detailed instructions for use are in the User's Guide.
[. . . ] HITACHI
COLOUR MONITOR
CM2111M I CM-2112M -* .
USER MANUAL
BEDIENUNGSANLNTUNG MANUAL DE USUARiO GEBRUIKSAANWIJZING MANUEL UTILISATEUR
. -
\ /
READ THE INSTRUCTION INSIDE CAREFULLY. For future reference, record the serial number of your colour monitor.
SERIAL No.
The serial number is located on the rear of the monitor.
EPA POLLUTION PREVENTER
This monitor is Energy Star compliant when used with a computer equipped with VESA DPMS, : The Energy Star emblem does not represent EPA endorsement of any product or service.
. , - r
-----
s-I---
c-<--
_
L i------ L. --A
-.
;
-A USER MANUAL ' IL 6 BEDIENUNGSANLEITUNG 1 9 ; m 1 E 35 i MANUAL DE USUARIO r. -:
COLOUR MONITOR
1 , I' . I, ~ :`a;
CM2111M CM2112M
F
USER MANUAL G 4 E
NOTE :
The information in this manual is subject to change without notice. HITACHI assumes no responsibility for any errors that may appear in this manual.
FEATURES . [. . . ] The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK. The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED.
6
3. Signal Cable Connection
0 For model CM21 12M, use a signal cable with a 13W3 Type D-Sub connector.
TABLE l-l 13W3Type D-Sub connectorTerminal
q
Insert connector to the "Signal Input Terminal" (13W3 Type D-Sub Connector Terminal), and secure the screws on the connector shell firmly.
0 For model CM21 11 M, use a signal cable with a D-Sub Mini 15-pin Connector.
TABLE 1-2
5 IO l5
D-Sub Mini 15-pin Connector Terminal
q
Insert connector to the "Signal Input Terminal" (D-Sub Mini 15-pin Connector Terminal), and secure the screws on the connector shell firmly.
0 If the graphics board supplies more than one type of sync. signal type will be automatically selected by the monitor, with the priority shown in TABLE 2.
TABLE 2
I
Sync. Power On
Turn on the Power Switch of the monitor first, then the computer. After turning OFF the switch, wait at least 5 seconds to restart the monitor. If the picture doesn't appear, turn OFF the power switch, make sure of the following and wait at least 30 seconds to restart the monitor. Make sure the power switch of the computer, power cord connection, signal cable connection and the input sync. If the colour is impure on the screen after turning ON the monitor, wait for 10 mlnutes and press the Degauss button.
8
icroprocessorstandard settings.
can store 31 sets of geometry settings including the
E.
~
The following industrial standard settings have been preprogrammed by the factory.
NOTE :
1. Remember, the monitor is automatically degaussed during initial power on. 0 Wait for 10 minutes before repeating the function.
MOIRE REDUCTION e Press the switch [ MOIRE I, to switch the Moire Reduction function ON/OFF. ON/OFF
While the button [ MOIRE ] is in the "ON" position, the moire changing circuit operates. You change the moire pattern by pressing this switch.
q
In some cases, this function may cause deterioration of display quality, such as focus, jitter, etc.
0 This function may be effected by outside magnetic fields.
!q
8OkHz/ 7%~ ; . . . -
0 Moire may appear on the screen due to an interference between the CRT dot pitch and video signal, and under certain conditions by video image, display size, display brightness, etc.
q
The symbol [a] will be indicated by pressing the button [a ] while this button is in the "ON" position.
IO
ADJUSTMENT
, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contrast
0 Press the button 10 1.
0 The EasyMenu will showthe input signal information with the contrast adjustment condition.
. 0 Pressthebutton[-]or[+].
[ + ] makes the display brighter, excluding the background. [ - I makes the display darker, excluding the background.
%j=t n
0 Press the button [ -0 I. Brightness -. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . m
3
Q Press the button [ - I or [ +I.
c %L -
.
z. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . :
[ + ] makes the display brighter, including the background. [ - ] makes the display darker, including the background.
m. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . m
Horizontal Position
;
0 Press the button I a 1.
i 0 Pressthebutton[-]or[+].
[ + ] moves the display position to the right. [ - ] moves the display position to the left.
ae
n
H. POSITION D+a i O-6
:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . :
. [ - ] shrinks the display vertically.
, "" _
;
77
-. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . m
. ; 0 Press the button [ - ] or [ +].
p
;
N D+o ;
[ + ] curves the left/right sides of the display outwards. [ - I curves the left/right sides of the display inwards.
77-
71
4;
- . . . . . . . [. . . ] Cl Storing the new setting will delete the old setting.
@ For the following items, only one setting is allowed :
STORED
!
@ Forthefollowing functions, one setting is allowed for each video mode : Horizontal Position, Horizontal Size, Vertical Position, Vertical Size, Pincushion, Trapezoid The setting will be restored to the picture automatically when the same video mode is used. Refer to "AUTOMATIC ADJUSTMENT".
q
For a video mode which already has a stored setting, storing the new setting will delete the old setting.
Cl The geometry for standard video modes has been preset (refer to "STANDARD SETTINGS"), and you can store maximum 31 sets of geometry settings including the standard settings. If your store is at its maximum already, storing a setting for new video mode overwrites the oldest user setting. 0 The video mode is distinguished by the horizontal/vertical frequency and polarity of the horizontal/vertical sync. [. . . ]