User manual JBL S36IIPM
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual JBL S36IIPM. We hope that this JBL S36IIPM user guide will be useful to you.
Manual abstract: user guide JBL S36IIPM
Detailed instructions for use are in the User's Guide.
[. . . ] It enables us to keep you posted on our latest advancements, and helps us to better understand our customers and build products that meet their needs and expectations. JBL Consumer Products
STUDIOTM SERIES S36IIPM
OWNER'S GUIDE
SPEAKER PLACEMENT
Proper placement of the speakers is an important step in obtaining the most realistic soundstage possible. These recommendations are for the optimal placement of the loudspeakers. [. . . ] Remember that the JBL logo on the tweeter/mid faceplate can be
Roof eave Supplied Angle-Mount Screw (When using angle-mount screws, always utilize the top two screw holes on the S36IIPM, depending on mounting orientation. ) Horizontal mounting: Use screwholes (1) and (2). Vertical mounting: Use screwholes (1) and (3), or (2) and (4), whichever are uppermost. Supplied Rubber Pad
S36IIPM
rotated with choice of speaker position (vertical or horizontal). At least one screw per speaker should be installed in a wooden wall stud. If the special angle-mount screws are not being used, size 10 screws of at least 1-1/2" in length are recommended. If the screws are used in drywall or other surfaces incapable of holding the screw by itself, selection of proper anchors is essential. The customer is solely responsible for proper selection and installation of screws, anchors and other installation hardware. Further installation details are included on the installation template.
Wall
Installation of Self-Adhesive Rubber Pads: If the speaker is to be placed on a surface (such as a table top or shelf) rather than wall-mounted, the enclosed selfadhesive rubber pads are to be attached to the bottom of the speaker cabinet in their designated recessed locations. If the speaker is to be wall-mounted, then the four self-adhesive rubber pads should be attached to the back of the speaker, as shown in the bottom right diagram. When angle-mounting the S36IIPM, only two of the rubber
pads are required, and they need to be installed on the back of the loudspeaker, near the lower edge, so that they are located between the back of the speaker and the mounting surface. NOTE: The threaded inserts on the bottom of the speakers are to be used only with JBL accessories that have been developed specifically for the S36IIPM and that may become available at a future date. Do not attempt to install bolts or any non-JBL brackets or acces-
sories to these threads, as this might damage the speaker and dislodge the insert.
PADS GO HERE
For tabletop or shelf placement
PLACE RUBBER PADS HERE
KEYHOLES FOR MOUNTING HARDWARE
For wall-mounting
SPEAKER CONNECTIONS CONNECTION TIPS
sound systems, connecting all of the speakers in your system with the correct polarity remains equally important in order to preserve the proper ambience and directionality of the program material. To use the binding-post speaker terminals, unscrew the collar until the pass-through hole in the center post is visible under the collar. Insert the bare end of the wire through this hole; then screw the collar down until the connection is tight. [. . . ] If the problem is in the same channel, the source of the problem is most likely with your receiver or amplifier, and you should consult the owner's manual for that product for further information. If the problem has followed the speaker, consult your dealer for further assistance or, if that is not possible, visit www. jbl. com for further information.
SPECIFICATIONS
S36IIPM
Description: 3-Way 6" horizontal/vertical mirror-image wall-mount/bookshelf loudspeakers for indoor and outdoor use Maximum Recommended Amplifier Power:**150W Nominal Impedance: 8 Ohms Sensitivity (2. 83V/1m): 90dB Frequency Response (3dB): 60Hz 20kHz Crossover Frequencies: 650Hz, 3000Hz High-Frequency Transducer: 1" Pure-titanium dome, with rubber surround, shielded; Elliptical Oblate SpheroidalTM (EOS) waveguide Midrange Transducer: 4" WeatherPlasTM (polymer-coated cellulose fiber) cone, rubber surround, shielded; Linear Field ProximityTM (LFP) bezel Low-Frequency Transducer: 6" WeatherPlasTM (polymer-coated cellulose fiber) cone, rubber surround, SFGTM magnetic shorting rings, high-temp oversized Kapton® voice coil, HeatScapeTM motor structure, , cast-aluminum baskets, shielded Baffles: Low diffraction, IsoPowerTM Enclosure: Sealed Network: Straight-Line Signal PathTM (SSP) Terminals: All-metal, gold-plated, 5-way binding posts Dimensions (H x W x D): 10-1/4" x 14-5/8" x 5" (260mm x 371mm x 127mm)
Declaration of Conformity
Weight: 11 lb/5kg
We, Harman Consumer International 2, route de Tours 72500 Chateau-du-Loir France declare in own responsibility that the loudspeakers described in this owner's manual
* Dolby is a trademark of Dolby Laboratories. **The maximum recommended amplifier power rating will ensure proper system headroom to allow for occasional peaks. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE JBL S36IIPM
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual JBL S36IIPM will begin.