User manual JBL S36

[. . . ] S P E C I F I C AT I O N S S36 Description: Maximum Recommended Amplifier Power*: Nominal Impedance: Sensitivity (2. 83V/1m): Frequency Response (­3dB): Crossover Frequencies: High-Frequency Transducer: 3-Way 6" horizontal/vertical mirror-image wall-mount/bookshelf loudspeakers 150W 8 Ohms 90dB 60Hz ­ 20kHz 650Hz, 3000Hz 1" Pure-titanium dome, with rubber surround, shielded; Elliptical Oblate SpheroidalTM (EOS) waveguide 4" PolyPlasTM (polymer-coated cellulose fiber) cone, rubber surround, shielded; Linear Field ProximityTM (LFP) bezel 6" PolyPlasTM (polymer-coated cellulose fiber) cone, rubber surround, SFGTM magnetic shorting , rings, high-temp oversized Kapton® voice coil, HeatScapeTM motor structure, cast-aluminum baskets, shielded Low diffraction, IsoPowerTM Sealed Straight-Line Signal PathTM (SSP) All-metal, gold-plated 5-way binding posts 10-1/4" x 14-5/8" x 5" 260mm x 371mm x 127mm 11 lb/5kg THANK YOU FOR CHOOSING JBL For more than 50 years, JBL has been involved in every aspect of music and film recording and reproduction, from live performances to the recordings you play in your home, car or office. We're confident that the JBL loudspeakers you have chosen will provide every note of enjoyment that you expected ­ and that when you think about purchasing additional audio equipment for your home, car or office, you will once again choose JBL. [. . . ] If the S36 is to be wallmounted, then the four selfadhesive rubber pads should be attached to the back of the speaker, as shown in the bottom right diagram. Please see your JBL dealer for more information. PADS GO HERE For tabletop or shelf placement PLACE RUBBER PADS HERE KEYHOLES FOR MOUNTING HARDWARE For wall-mounting SPEAKER CONNECTIONS CONNECTION TIPS speakers identically: (+) on the speaker to (+) on the amplifier and (­) on the speaker to (­) on the amplifier. Wiring "out of phase" results in thin sound, weak bass and a poor stereo image. With the advent of multichannel surround sound systems, connecting all of the speakers in your system with the correct polarity RIGHT LEFT For home-theater applications: 0-2 ft. This placement provides a wide spread in sound, supplemented by the center-channel speaker. ­ + ­+ ­ + ­ + Speaker Outputs The S36 loudspeakers may be positioned on the wall either horizontally or vertically. The grille logo on each speaker may be rotated depending on how the speaker is positioned. Gently pull the logo away from the grille slightly, rotate it to the desired position, and let go. When mounted vertically, the tweeter array may be positioned either up or down, depending on the height of the placement. If the speakers will be above ear level, the tweeter array should be positioned down, preferably no more than two feet above ear level. If the speakers will be mounted very low, it may be best to position the tweeter array upward so that it will be no more than two feet below ear level. Speakers and electronics terminals have corresponding (+) and (­) terminals. It is important to connect both remains equally important in order to preserve the proper ambience and directionality of the program material. TROUBLESHOOTING If there is no sound from any of the speakers: · Check that receiver/ amplifier is on and that a source is playing. [. . . ] The customer is solely responsible for proper selection and installation of screws, anchors and other installation hardware. Further installation details are included on the installation template. Declaration of Conformity We, Harman Consumer International 2, route de Tours 72500 Chateau-du-Loir France declare in own responsibility, that the loudspeaker described in this owner's manual is in compliance with technical standards: EN 50081-1:1992 EN 50082-1:1992 TV Steen Michaelsen Harman Consumer International France. [. . . ]