User manual JBL SYN-K2
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual JBL SYN-K2. We hope that this JBL SYN-K2 user guide will be useful to you.
Manual abstract: user guide JBL SYN-K2
Detailed instructions for use are in the User's Guide.
[. . . ] Indd 2
04/09/08 16:26:51
FCC STATEMENT AND WARNING
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] Connect the standard cable for iPod to the rear of the JBL On Time 200ID unit, and every time you dock your iPod, you’ll have a connection for synchronizing. EVERCHARGE TOPOLOGY The JBL On Time 200ID speaker dock charges your iPod, even when it’s not connected to the computer or the system is off. COE (COMPUTER-OPTIMIZED EQUALIZATION) The JBL On Time 200ID system equalization is computer-optimized to provide a rich, complete soundstage. OCT (OPTIMIZED COMPRESSION TOPOLOGY) The JBL On Time 200ID radio and loudspeaker dock utilizes a proprietary compression technology to ensure clean, accurate sound at high output levels. DISPLAY The large, backlit LCD enables easy viewing and menu navigation. Automatic dimming sets the correct brightness level in any room environment. Indd 4
04/09/08 16:26:51
UNPACKING YOUR JBL ON TIME™ 200ID
Carefully unpack your speaker system and identify all its components: IR remote FM antenna
JBL On Time™ 200ID
Adapters for iPod
Power supply
Audio cable
AM antenna
QUICK SETUP INSTRUCTIONS
• • • • • •
Choose the appropriate adapter for iPod and place it into the docking station. For backup memory, install three AAA batteries in the battery compartment underneath the unit. Plug the power adapter into the “DC In” jack and then plug the adapter into a wall outlet. If an additional audio source is used, connect the source to the “Aux In” jack. Press Menu/Up Level at any screen to display Top Menu (may require repeated presses, depending on which menu state the unit was previously in). A single press starts sleep time countdown, using currently set timer. Press and hold for 2 seconds to enter Sleep Timer setting screen (similar to base unit). When iPod is the active source, a single press sends the Play/Pause command to the iPod. When AM, FM or AUX is the active source, a single press mutes audio/amp on the JBL On Time 200ID system. Indd 10
04/09/08 16:26:55
JBL ON TIME™ 200ID MENU TREE
Now Playing (ON) Now Playing (Off)
Clock
Alarm
Display
Sleep
Region
12H
24H
HOT KEY POINT (on remote or base unit)
AL1-AL7 Brightness Contrast
HOT KEY POINT (on remote)
HR
HR set sleep timer: 15-30-60 A Selection command displays setting confirmation and returns state to Top Level Menu screen. Min
Min Select Alarm
Set Language: English Spanish French German Italian Dutch
am/pm Hr set day Press and hold for 2 sec at any point in menu structure, to return to now Playing screen. )
PRESET
HOT KEY POINT (on remote or base unit)
SOURCE
HOT KEY POINT (on remote or base unit)
SNOOZE
HOT KEY POINT (hold button for 3 sec on base unit)
SNOOZE
Preset 1-10
Press and hold Preset button while listening to radio to store current station. Indd 12
04/09/08 16:27:01
SPECIFICATIONS
JBL ON TIME™ 200ID
Frequency Response: 70Hz – 20kHz Power Consumption: 30 Watts maximum JBL On Time™ 200ID Transducer: Phoenix SE 1-3/4" (45mm) x 2 (full range per channel) Power: 2 x 6 Watts Input Impedance: >5k Ohms Signal-to-Noise Ratio: >80dB Input Sensitivity: 350mV RMS for rated power output Power (USA/Canada): 120 Volts, 60Hz AC Power (Europe/UK): 220 – 230 Volts, 50Hz or 60Hz AC Power (Japan): 100 Volts, 50Hz or 60Hz AC Power (Australia): 240 Volts, 50Hz or 60Hz AC UL/CUL/CE-Approved Dimensions: 11-3/16" x 5-3/4" x 2-3/4" (W x D x H) (284mm x 146mm x 70mm) Weight: 1. 8kg) Remote Battery: CR2025
TROUBLESHOOTING
SOUND QUALITY Symptom
No sound from the JBL On Time™ 200ID unit
Possible Problem
No power to the unit
Solution
Make sure the wall power outlet or power strip has power. Make sure all switches for outlet/ power strip are on and that all switches for speaker system are on. Make sure the correct source is selected; choose FM radio as a source. [. . . ] Tryck på enter för att bekräfta, eller tryck på alarm för att gå direkt till alarm-menyn. En symbol visas till vänster
Programmera Välj upp
Meny/Upp en nivå
Enter
Välj ner
Vakna upp till din iPod
1. VIKTIGT: Använd endast icke uppladdningsbara alkaliska batterier av typ UM4/AAA/LR3
FELSÖKNING
LJUDKVALITET Symptom
Det kommer inget ljud från JBL On Time™ 200ID
Möjligt problem
Ingen ström kopplad till enheten
Lösning
Se till att det finns spänning i vägguttaget eller elanslutningen. Se till att alla brytare till uttag eller anslutning är påslagna, och att alla brytare på högtalarsystemet är på. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE JBL SYN-K2
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual JBL SYN-K2 will begin.