User manual JURA IMPRESSA SCALA

[. . . ] IMPRESSA M30 IMPRESSA Scala IMPRESSA Scala Vario IMPRESSA X30 Instructions for use Art. 6 ­ 17 Legend : = Note = Important = Tip Jura Elektroapparate AG, CH-4626 Niederbuchsiten, Internet http://www. juraworld. com Kundendienst Telefon 062 389 82 33 Fig. 9 Operating elements Jura Impressa M30 11 12 13 10 14 15 16 17 18 19 9 8 7 6 5 4 3 1. 19. Drip tray / Residual water container Drip tray cover Water volume selector switch Draw-off button 2 cups Draw-off button 1 cup Selector switch powder coffee Rinsing button ON/OFF switch Symbol field with warning lamps Water tank with handle Cover of bean container with aroma-protection lid Cover of funnel for pre-ground coffee powder Cup support Steam selector switch Selector switch for steam/hot water Coffee spout Pivoting nozzle for hot water/steam Frothing nozzle Grounds container 2 1 Contents Jura Impressa M30 1. [. . . ] If no water hardness level is changed within 60 seconds, the display goes out and the last value programmed remains unchanged. If no change to the setting level is made within 60 seconds, the warning lamps go out and the last level stored remains effective. 4. The warning lamp and the small light in the steam selector switch (14) flash. Turn the selector switch for steam/hot water (15) back to the position. 3. 8 Adjustable automatic close-down You can adjust the automatic close-down of 2 hours set by Jura to your own requirements. The machine provides 3 different levels: 1st Level Warning lamp flashes. 2nd Level Warning lamp flashes, warning lamps Automatic close-down is set to 2 hours. Rinsing the machine If warning lamp light up, the machine needs rinsing. , If the machine has been switched off and has already cooled down it will be necessary to carry out this rinsing function when the machine is switched on again. After switching off the machine, the rinsing sets off automatically. E , , , To set or alter the automatic close-down follow the instructions below: Put the mains plug into the wall socket. Press draw-off button for about 3 seconds and choose the required setting by pressing selector switch. Adjusting water volume Water volume is infinitely adjustable by means of the selector switch (3). Avoid direct contact with the skin. 7. 1 Drawing off espresso/strong coffee Place 1 cup under coffee-spout (16) and press the required button until the warning lamp lights up. You can only draw off 1 cup of strong coffee at a time. 7. 2 Drawing off powder coffee Press selector switch. Warning lamps and light up. Now put 1 or 2 levelled spoons of pre-ground coffee powder into the filling funnel for pregrownd coffee powder (12) (Fig. Place 1 or 2 cups under coffee-spout (16) and press the coffee button required. 10 8. 1 Resetting to stand-by status Please the selector switch (14) once more. Clean the pivoting nozzle with a moist cloth after every draw-off of steam. 11. 2 Empty grounds container The coffee grounds are collected in the grounds container. When the warning lamp lights up, the draw-off buttons are blocked and you must empty the grounds container. Drawing off hot water Place a cup under the pivoting nozzle (17) and turn the selector switch for steam/hot water (15) to the position. In order to end the process, turn the selector switch for steam/hot water (15) back to the position. When hot water is first drawn off, there is a possibility of spattering and the risk of scolding. Avoid direct contact with the skin. 11. 3 Drip tray is missing If the drip tray is not replaced correctly, warning lamp flashes. When the drip tray is outside the machine you can take the opportunity to clean the inside of the machine. Then replace clean drip tray. E 11. 4 Removing foreign objects Switch your machine off with the switch. Now turn the wrench in an anti-clockwise direction until the jammed foreign body comes loose. [. . . ] The flashing of the warning lamps reminds you that the de-scaling process is activated. The de-scaling solution is guided into the drip tray in the inside of the machine. The small light in the selector switch (14) and the warning lamp flash. Place a container under the pivoting nozzle (17) and press the rinsing button. [. . . ]