User manual JURA IMPRESSA X90

[. . . ] = Note = Important = Tip Jura Elektroapparate AG, CH-4626 Niederbuchsiten, Internet http://www. juraworld. com Fig. 13 12 13 14 15 16 D 11 10 9 8 7 6 5 4 3 23 17 18 19 20 21 22 A B C E F G H 2 1 Instructions for use 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21. 22 23 Drip tray / residual water container Drip tray cover Cover for programming keys Coffee key for 2 large cups Coffee key for 1 large cup Coffee key for 2 small cups Coffee key for 1 small cup Key for special coffee ON/OFF switch Rinsing key Display dialogue system Water tank with carrying handle Cover for bean container and aroma protection lid Cover for pre-ground coffee filler funnel Height-adjustable coffee-spout Cup warming tray Selector key for steam Selector key for steam portion Selector switch for coffee or hot water (TAP) Replaccable steam/frotting nozzle Profi Auto-Cappuccino/Caffè Latte Height-adjustable tea-spout Container for coffee grounds Programming keys A B C D E F G H Change filter Back-setting of criteria / changing of memory indications downwards Open program Selector switch for pre-ground coffee Key for cleaning program Correction of program / close Forward-setting of criteria / changing of memory indications upwards Key for decalcifying program Table of contents 1. Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2. [. . . ] 11). 11. 2 Cleaning the Profi-Auto-Cappuccino/ Caffè Latte The Profi-Auto-Cappuccino/Caffè Latte (21) must be cleaned after each draw-off operation. If necessary, disassemble the Profi-Auto-Cappuccino/Caffè Latte and thoroughly rinse the flow regulation with water (Fig. For proper cleaning, use the Jura Auto Cappuccino Cleaning Agent which is available at your authorized dealer. 11. 1 Drawing off cappuccino and hot milk with Profi-Auto-Cappuccino/Caffè Latte Fill the milk container with milk or immerse the hose in the milk directly. Press the steam portion draw off key STEAM PORTION The frothing/heating time depends on the steam portion settings you have programmed. Switching off machine When the machine is switched off, the rinsing program is automatically run again. Therefore place an empty container under the coffee-spout (15) and press ON/OFF key . When the rinsing water has run into the container, the machine powers down. Programming Before leaving our factory, the machine is adjusted to enable you to obtain coffee without any additional programming. In order to adapt the result to your personal taste, various settings can be programmed individually. The following settings can be programmed: Powder quantity Coffee temperature Water quantity Steam portion Tea portion Filter Water hardness Economy mode Timer clock Automatic switch on time Automatic switch off time Supplies and cup counter Language selection To store the new powder quantity in memory briefly press key P . By pressing the + button, you can select the next phase, or press the N button in order to leave the programming. 13. 2 Programming coffee temperature TEMPERATURE COFFEE / SELECT KEY Now press the key that you want to programme. Select the required temperature (high or normal) by activating key + or - . TEMPERATURE COFFEE / SELECT KEY By pressing the + button, you can select the next phase, or press the N button in order to leave the programming. 13. 3 Programming water quantity WATER QUANTITY / SELECT KEY Put a cup under the coffee-spout (15) and then press the key that you want to programme. P - ·········· II ·········· + When the required water quantity is reached press key P . If you wish to draw another coffee to control the water quantity, press key again otherwise press key P briefly to store water quantity in memory. 13 E 13. 1 Programming powder quantity Switch the machine on by pressing ON/OFF key . Press key POWDER QUANTITY / SELECT KEY Now press the key that you want to programme. The corresponding quantity for 2 cups is adjusted automatically by the machine after programming is finished. POWDER - ·········· II ·········· + The powder quantity can be selected by pressing keys + or briefly. By pressing the + button, you can select the next phase, or press the N button in order to leave the programming. 13. 7 Programming water hardness (only with setting Filter no) HARDNESS LEVEL 3 Press key P By pressing key + or - briefly you can programme the water hardness level. By pressing the + button, you can select the next phase, or press the N button in order to leave the programming. "Adjusting for water hardness". 13. 4 Programming steam portion STEAM PORTION . By pressing key + or - you can programme time in seconds (drawing off time of 3 ­ 250 sec. ) Press key P . STEAM PORTION By pressing the + button, you can select the next phase, or press the N button in order to leave the programming. [. . . ] CLEAN CONTACTS / EMPTY TRAY (please refer to chapter 14. 8) PLEASE WAIT RINSE UNIT UNIT RINSING COFFEE READY 17. Disposal For correct disposal, you should return your coffee machine to your dealer, Jura service centre or Jura Elektroapparate AG. 18. Tips for a perfect coffee Height adjustable coffee-spout You can adjust the height of the coffee-spout to the size of your cups. Pre-warm cups You should warm cups in advance with hot water or steam. [. . . ]