User manual MARANTZ AV7701

[. . . ] Basic version Advanced version Information AV Pre Tuner AV7701 Owner?s Manual DVD n SAFETY PRECAUTIONS RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated ?dangerous voltage?within the product?s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. 1. 2. 3. 4. 5. 6. 7. 8. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. Read these instructions. [. . . ] in GExample 3H Q0 To adjust the main volume, click ?<?, ?>?, or the volume display. Q6 The sound mode switches each time you click the button. Q7 Click the menu item from which you want to make settings. GExample 3H Web configuration screen Web Controller Config. W3 Click to return to the previous screen. W5 Use to operate content. Information W1 W2 Top Menu Link Setup Back Top Menu ON OFF W1 Click ?ON?(Default setting : ?OFF?) W2 Click this item to return to the top menu. DVD 96 Dual backup memory function The unit stores settings information in nonvolatile memory even when the main power supply is turned off. Using the Dual Backup Memory function, you can write settings information to another memory area to back up saved settings for recovery anytime as needed. Remembering set details (Backup). Panel lock function To prevent accidental operation of this unit, you can disable operation of the buttons on the front panel. Basic version BACK ui ENTER BACK Advanced version X ON/STANDBY DISPLAY ZONE SELECT nnRemembering set details (Backup) Set the unit in the state you want remembering, and press and hold DISPLAY and ZONE SELECT for at least 3 seconds. ?MEMORY SAVING?is shown in the display, and the setting details are remembered. nnDisabling all key button operations NOTE ? The volume is not remembered. ? If remembered details are overwritten, the previously remembered contents are deleted. 1 Press X ON/STANDBY while you press and hold BACK and ENTER with the unit in standby mode. 3 Press ENTER to enter the setting. All button operations except X ON/STANDBY are disabled. Information nnRecalling remembered details (Recovery) Press and hold BACK and ZONE SELECT together for at least 3 seconds. ?MEMORY LOAD?is shown in the display, and the remembered details are recalled. nnDisabling all button operations except VOLUME NOTE ? If there is no remembered data, ?NO BACKUP?? As the volume cannot be recalled, it returns to the factory setting volume. 1 Press X ON/STANDBY while you press and hold BACK and ENTER with the unit in standby mode. 3 Press ENTER to enter the setting. All button operations except X ON/STANDBY and VOLUME are disabled. v See overleaf DVD 97 Panel lock function nnCanceling the Panel lock function Remote lock function ? When not connecting an IR receiver, disable the Remote lock function. When the function is enabled, you can not perform operations with the remote control unit. ? By default, this function is disabled. Basic version 1 Press X ON/STANDBY while you press and hold BACK and ENTER with the unit in standby mode. 3 Press ENTER to enter the setting. (z The currently set mode. ) The Panel lock function is canceled. Even when the Panel lock function is set, you can operate the unit using the remote control unit. BACK ui ENTER Advanced version X ON/STANDBY nnDisabling the sensor function of the remote control unit When the 1 down BACKmain unit is in standby mode, press X ON/STANDBY while holding and ENTER on the main unit. 3 Press ENTER to enter the setting. The infrared light receiving function is disabled. Information nnEnabling the remote sensor function When the 1 down BACKmain unit is in standby mode, press X ON/STANDBY while holding and ENTER on the main unit. 3 Press ENTER to enter the setting. (z The currently set mode. ) The infrared light receiving function on the main unit is enabled. DVD 98 Switches light illumination on/off ? You can switch the lighting around the main display on or off. ? The factory setting is ?ON?. Various memory functions Basic version Personal memory plus function This function sets the settings (input mode, sound mode, HDMI output mode, MultEQ XT, Dynamic EQ, audio delay etc. ) last selected for the individual input sources. The surround parameters, tone settings and the volumes of the different speakers are stored for the individual sound modes. Last function memory DISPLAY Press and hold DISPLAY on the main unit for 3 seconds. This function stores the settings which were made before going into the standby mode. When the power is turned back on, the settings are restored. Advanced version ? Carry out the same procedure if you want to change the settings again. Information DVD 99 Playback in ZONE2/ZONE3 (Separate room) ? You can operate this unit so as to enjoy audio in a room (ZONE2, ZONE3) other than the MAIN ZONE (room where the unit is located). ? You can simultaneously play back the same source in both the MAIN ZONE, ZONE2 and ZONE3. [. . . ] Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. edistributions of source code must retain the R above copyright notice, this list of conditions and the following disclaimer. 2.  edistributions in binary form must reproduce R the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. DVD LICENSE 3.  he names of its contributors may not be used T to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS ?AS IS?AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. [. . . ]