User manual MARANTZ CC4001 Product Manual

[. . . ] Model CC4001 User Guide CLASS 1 LASER PRODUCT LUOKAN 1 LASERLAITE KLASS 1 LASERAPPARAT CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL LASER SAFETY This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to possible eye injury. CAUTION : USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURE OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPON-DANTE DE LA PRISE ET POUSSER JUSQU'AU FOND. IMPORTANT SAFETY INSTRUCTIONS READ BEFORE OPERATING EQUIPMENT This product was designed and manufactured to meet strict quality and safety standards. There are, however, some installation and operation precautions which you should be particularly aware of. [. . . ] While this button is pressed during playback, the track is searched forward. /4 RECALL button Use this button to check the programmed tracks while programming or stopped programming. (See page 16) z x c STANDBY ON When this button is pressed while the unit is in standby status, the power of the unit is turned on. OPEN/CLOSE TIME DIMMER /7 /6 x STANDBY button When this button is pressed while the power is on, the unit goes into the standby status. /5 0 -9 (Numerical buttons) Use these buttons to choose tracks and to input track number in each mode. 1 4 7 PROGRAM 2 5 8 0 3 6 9 RECALL m RANDOM button Playback tracks randomly. (See page 14) c 0 OPEN/CLOSE button /6 TIME button This button is used to switch the time display. Each time it is pressed, the displayed time cycles from "track elapsed time" "track remaining time" "total remaining time" "track elapsed time". Press the button again to close the tray. , DISC1-DISC5 (Disc Select button) Choose a disc to play. v Caution Do not press the disc tray in by hand. Use this button also to switch to the Repeat mode (One Track Repeat, One Disc Repeat, and All Disc Repeat). (See page 15) /7 DIMMER button This button is used to adjust the brightness of the display window. v PROGRAM button This button is for program play. (See page 15) b /1 n m , RANDOM AMS REPEAT b 4, ¢ (Track Skip buttons) 4: When this button is pressed, the unit goes back to the beginning of the current track. If the button is pressed more times, the track being played is skipped back. ¢: Each time this button is pressed, the track being played is skipped forward. · Search buttons are provided separately for the remote control unit. Use n Search buttons for search function. /0 AMS (Automatic Music Scan button) Use this button for AMS play. (See page 13) /0 . /1 7 STOP button Press this button to stop playback. Also this button is used to clear programs. DISC 1 DISC 2 DISC 3 DISC 4 DISC 5 /2 8 PAUSE button Press this button to pause playback. If pressed again, the unit returns to playback. REMOTE CONTROLLER RC4001CC /3 3 PLAY button Press this button to start playback. 8 NAMES AND FUNCTIONS REMOTE CONTROL CODE SETTING · The unit and remote control unit have five sets of built-in remote control codes for each. These codes enable up to five CC4001s installed in the same place to be controlled independently. · To use multiple units at the same time, set the second, third, forth, and fifth CC4001s and their remote control units' remote control codes. · To set the codes, follow the procedure below to control only selected unit is remotely controlled. · At the factory, the unit and remote control unit were set to CODE1. 7 Remote Control Unit Setting STANDBY ON 7 CC4001 Setting STANDBY ON Display Examples · When the remote control unit is set to CODE1 1 2 CD OPEN/CLOSE TIME DIMMER OPEN/CLOSE TIME DIMMER 3 4 DISC 1 4 7 PROGRAM 2 5 8 0 3 6 9 RECALL 1-5 1 4 7 PROGRAM 2 5 8 0 3 6 9 RECALL 5 1 6 11 16 2 7 12 17 3 8 13 18 4 9 14 19 5 10 15 20 RECALL PROGRAM RECALL · When the remote control unit is set to CODE2 1 2 3 4 5 DISC 1 6 11 16 2 7 12 17 3 8 13 18 4 9 14 19 5 10 15 20 CD RANDOM AMS REPEAT RANDOM AMS REPEAT DISC 1 DISC 2 DISC 3 DISC 1 DISC 2 DISC 3 DISC 4 DISC 5 DISC 4 DISC 5 · When the remote control unit is set to CODE3 REMOTE CONTROLLER RC4001CC REMOTE CONTROLLER RC4001CC 1 2 3 CD · To set CODE2 Press RECALL button and Numerical button 2 on the remote control unit at a time for five seconds or more. · To set CODE3 Press RECALL button and Numerical button 3 on the remote control unit at a time for five seconds or more. · To set CODE4 Press RECALL button and Numerical button 4 on the remote control unit at a time for five seconds or more. · To set CODE5 Press RECALL button and Numerical button 5 on the remote control unit at a time for five seconds or more. · To synchronize the remote control code of the CC4001 with the remote control unit, press the PROGRAM and RECALL buttons on the remote control unit together. [. . . ] Or press 0 OPEN/CLOSE button and open the disc tray to clear the whole program. When the unit switches to standby or power off, the programs are all erased. 1 2 3 4 5 TRACK DISC MIN SEC 7 3 CD PROGRAM Total number of programs Total playback time of the tracks programmed · In this example, as a track on a disc that is not selected is included in the program, "-- : --" is displayed for the total playback time for the programmed tracks. 17 ENGLISH CLEAR PROGRAMMED TRACKS 7 To Clear One Track at a Time 7 To Clear Chosen Track STANDBY ON 7 To Clear Whole Program STANDBY ON DISPLAY WINDOW BRIGHTNESS ADJUSTMENT ENGLISH STANDBY ON SWITCHING PLAYING TIME DISPLAY STANDBY ON OPEN/CLOSE TIME DIMMER OPEN/CLOSE TIME DIMMER DIMMER 1 4 7 PROGRAM 2 5 8 0 3 6 9 RECALL 1 4 7 PROGRAM 2 5 8 0 3 6 9 RECALL TIME · When a program is set up using tracks from only currently selected disc the amount of time remaining in the program is displayed. (Except for MP3 discs) When a program is setup with discs that are not selected, "-- : --" is displayed for the total program time. · If the total playback time of the tracks programmed exceeds 99 minutes 59 seconds, "-- : --" is displayed for the remaining program time. RANDOM AMS REPEAT RANDOM AMS REPEAT DISC 1 DISC 2 DISC 3 DISC 1 DISC 2 DISC 3 DISC 4 DISC 5 DISC 4 DISC 5 REMOTE CONTROLLER RC4001CC REMOTE CONTROLLER RC4001CC Each time DIMMER button on the remote control unit is pressed, the display window brightness changes as follows: Each time TIME button on the remote control unit is pressed, the display of the playing time changes as follows: Elapsed time of playing track 1 2 3 4 5 TRACK DISC MIN SEC 7 8 9 10 11 12 13 14 15 16 17 18 19 20 CD Remaining time of playing track 1 2 3 4 5 EACH REMAIN TRACK DISC MIN SEC 7 8 9 10 11 12 13 14 15 16 17 18 19 20 CD Remaining time of playing disc 1 2 3 4 5 TRACK DISC TOTAL REMAIN MIN SEC 7 8 9 10 11 12 13 14 15 16 17 18 19 20 CD · While playing MP3, the disc remaining time is displayed as "- - : - -". [. . . ]