User manual MARANTZ MD2020

[. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: This Class B digital apparatus complies with Canadian ICES-003. NOTE: Changes or modifications may cause this unit to fail to comply with Part 15 of the FCC Rules and may void the user's authority to operate the equipment. Cet appareil numerique de la Classe B est conforme a la norme NMB-003 du Canada. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. [. . . ] · Furthermore, the following functions are not available during 7. 1 CH Input use. Test Tone, NIGHT MODE, Source Direct, Pure Direct, RE-EQ, Tone Control, Multi EQ. 3. 3. 3. 3. 4. 46 ENGLISH NAMES AND FUNCTION OTHERS TROUBLESHOOTING REMOTE CONTROLLER ADVANCED OPERATION BASIC OPERATION SETUP CONNECTIONS AUX INPUT If you don't need to connect 7. 1 Ch. input terminals with multi channel decoder, L(front left) and R (front right) inputs terminals are available as AUX input. In this case, You can connect additional audio source to AUX as other audio input terminals. TV AUTO ON/OFF FUNCTION This function allows the component connected to the TV-VIDEO in jack to control the power (ON/OFF) to the unit. LIP. SYNC Depending on the image device (TV, monitor, projector, etc. ) connected to the unit a time lag can occur between image signal processing and audio signal processing. Though minor, this time lag can interfere with movie and music enjoyment. SYNC feature delays the audio signal with respect to the image signal output from the unit to correct the time lag between the sound and image. It can be operated with the "LIP. SYNC" and 1 and 2 cursor buttons of the remote controller. To select Lip-sync mode, set the remote controller to the AMP mode, press the < / > button until 002 is displayed. The initial setting is OFF (0 ms). The time lag can be adjusted in 10 ms steps up to 200 ms. Watch the picture on the image device (i. e. , TV, monitor, projector, etc. ) as you adjust the time lag. STANDBY POWER ON/OFF DUAL BACKUP MEMORY The unit stores settings information in nonvolatile memory even when the main power supply is turned off. 3. MEMORY NO LOAD BACKUP Note: · Because the following settings values are not backed up, each Volume value is set to Minimum. · Main Zone Volume · Zone Volume · Zone Speaker Volume 1. Press the 3 or 4 cursor buttons on the front Panel for more than 1 second to start the auto tuning function. Automatic searching begins then stops when a station is tuned in. 1. Press the AMP button. 4. (Using the remote controller) 3. 1. Automatic searching begins then stops when a station is tuned in. Press the < / > button until 008 is displayed. Press the TUNER button. 48 ENGLISH NAMES AND FUNCTION OTHERS TROUBLESHOOTING REMOTE CONTROLLER ADVANCED OPERATION BASIC OPERATION SETUP CONNECTIONS Note: The same operations performed using the 3/ 4 buttons can be performed using the ­ TUNE + button of item 002 when the remote controller is in TUNER mode. If tuning does not stop at the desired station, use to the "Manual Tuning" operation. DIRECT FREQUENCY CALL In TUNER mode, press the T-MODE button on the remote controller to switch between AUTO STEREO and monaural sound. PRESET MEMORY With this unit you can preset up to 60 FM/AM stations in any order. For each station, you can memorize the frequency and reception mode if desired. 3. 3. 1. Each time the T-MODE button is pressed, the TUNER mode changes and the mode is displayed on the FL display. AUTO PRESET MEMORY This function automatically scans the FM and AM band and enters all stations with proper signal strength into the memory. MANUAL TUNING 1. PURE DIRECT M-DAX 3. AV PRE TUNER MD2020 2. UP HDMI 2. 4. 2. Analog / Digital Auto Mode T-MODE:DIG-AT For listening to HD Radio stations. [. . . ] Because the room causes variations in the frequency response of the loudspeakers that are so large from seat to seat, it is important to measure each loudspeaker at several locations in the listening room. Measurement at a single location is not representative of the acoustical problems in the room and will in most cases, degrade overall performance. Audyssey MultEQ is the only technology that can achieve room correction for multiple listeners in a large listening area. It does so by combining the data collected at several points in the room from each loudspeaker and then applying correction that minimizes the acoustical effects of the room and is matched to the frequency resolution of human perception (known as psychoacoustics). [. . . ]