User manual MARANTZ MOUNT20

[. . . ] Model MOUNT20 User Guide VP-12 Series Projector Ceiling Mount MOUNT20 IMPORTANT SAFETY INSTRUCTIONS READ BEFORE INSTALLING EQUIPMENT This product was designed and manufactured to meet strict quality and safety standards. There are, however, some installation and operation precautions which you should be particularly aware of. 1. [. . . ] Special techniques and experience are required when installing the projector with this mount. Once the projector is installed, safety checks should be conducted on a regular basis. 8 5/8" VP-12 SERIES PROJECTOR CEILING MOUNT INSTALLATION INSTRUCTIONS Step 1 Base Plate Connectors #1 and Projector Mount Ceiling Plate 1 with ceiling mounting holes #2. Figure 1 1 4 Ceiling Wire Access 4 14" 2 3 2 3 2 Plate 1 Base Plate Connectors #1 Projector Mount Ceiling Plate 1 Insert Base Plate connectors #1 into the lateral positioning slots #3 as shown in #4 from the underside of Plate 1. The lateral positioning slots will give you 2 1/4" inches of lateral adjustment for projector alignment. Warning The ceiling should be capable of supporting a weight of at least five (5) times the projector(s) weight. Proper installation procedure by qualified personnel as outlined in the installation instructions must be adhered to. Failure to do so could result in serious personal injury. Step 2 Horizontal Adjustment Plate 2 (Base Plate Connector Holes #3). Figure 2 3 3 Wire Access 10 5/8" Hardware List 1. Four (4) 3/8 (inch) nuts Four (4) 3/8 (inch) flat washers Two (2) 8 (mm) screws Eleven (11) 6 (mm) screws Eight (8) 6 (mm) rubber washers 6. One (1) Ceiling Mount #1 Two (2) Base Plate Connectors One (1) Horizontal Tilt Plate #2 One (1) Horizontal Tilt Plate #3 One (1) Projector Plate #4 3 3 7 5/8" Adjustment Ranges and Load Allowances Horizontal Tilt (yaw) Vertical Tilt (tilt) Rotation Lateral Shift Maximum Load Allowance +/+/+/+/10 degrees 20 degrees 15 degrees 21/4 inches 450 Lbs. Plate 2 Base plate connector holes #3 provide 15 degrees of horizontal rotation adjustment. Attach horizontal adjustment Plate 2 to projector mount ceiling Plate 1 using the four (4) 3/8" (inch) nuts and washers provided. MOUNT20 PROJECTOR CEILING MOUNT INSTALLATION INSTRUCTIONS continued Step 2 B Horizontal Adjustment Plate 2 (Figure 2) attached to Projector Mount Ceiling Plate 1. Figure 3 Step 3 B Horizontal Tilting Plate 3 Attached to Plates 1 and 2. Figure 5 Wire Access Tilting Capability Tilting Capability Plates 1 & 2 Plate 3 Install the combined plates (above) securely to the ceiling structure in accordance with local commercial building standards. [. . . ] Lift and slide the projector onto the 6 (mm) screws previously installed in the metal studs of the plate on the ceiling (see arrow in Figure 7). Tighten the 6 (mm) screws on both sides of the mount and install four (4) 6 (mm) screws and washers into the side of the projector Mounting Plate 4. Sequence of Assembly of Projector Mounting Plates Plate 1 Step 2 Plate 2 Step 3 Plate 3 Step 4 Plate 4 1100 Maplewood Drive Itasca, IL 60143 Phone: 630 741-0300 Fax: 630 741-0301 You can find your nearest authorized distributor or dealer on our website at: www. marantz. com Printed in Canada 2004 Dimensions PLATE #1 14. 00" 5. 5" 5. 5" 0. 9" 10. 0" 1. 7" 3. 8" 7. 0" 8. 5" 3. 15" 1. 0" 2. 5" CEILING SIDE 2. 75" 2. 5" 3. 8" 1. 7" Base Plate Connectors 6. 50" 5. 00" 1. 375" You can find your nearest authorized distributor or dealer on our website at: www. marantz. com 1100 Maplewood Drive Itasca, IL 60143 Phone: 630 741-0300 Fax: 630 741-0301 Printed in Canada 2004 [. . . ]