User manual MARANTZ PD4298HD

[. . . ] Slim Line Plasma Monitor PD4298HD USER MANUAL MANUEL UTILISATEUR MANUAL DE USUARIO READ THE INSTRUCTIONS INSIDE CAREFULLY. For future reference, record the serial number of your monitor. SERIAL NO. The serial number is located on the rear of the monitor. NOTE: The information in this manual is subject to change without notice. The manufacturer assumes no responsibility for any errors that may appear in this manual. TRADEMARK ACKNOWLEDGEMENT VGA and XGA are registered trademarks of International Business Machines Corporation. [. . . ] The batteries could explode or leak, resulting in fires, physical injury, or stains. CAUTIONS s When loading batteries, observe their correct polarities as marked on the product. If loaded in the wrong direction, the batteries could explode or leak, resulting in fires, physical injury, or stains. s TIPS Do not drop or impact the remote controller. Do not splash the remote controller with water or put it on a wet object to avoid possible failures. s Before leaving the remote controller out of use for an extended period of time, remove the batteries from it. s If the remote controller begins to lack responsiveness, replace the batteries. s Strong light such as direct sunlight impinging on the photoreceptor of the remote control can cause operational failure. Position this unit to avoid direct contact with such light. s s OPERATING INSTRUCTIONS Turning Power On and Off unit to ON and then press the SUB POWER button or the POWER ON or POWER SOURCE ON/OFF button of the remote controller. q To turn off the main unit power supply, press the SUB POWER button of the main unit or the POWER OFF or POWER SOURCE ON/OFF button of the remote controller, then main unit the MAIN POWER switch ( ) to OFF. s For normal operations, leave the MAIN POWER switch ( ) main unit to ON and use the SUB POWER button or the POWER ON or POWER SOURCE ON/OFF button of the remote controller to turn the power on and off. Indicating lamp Off Power status Off Operating When the MAIN POWER switch set to OFF. is Lights red Off (standby) When the MAIN POWER switch is set to ON and POWER OFF or POWER SOURCE ON/OFF button of the remote controller or the SUB POWER button on the main unit located at the front part of the bottom plate is off. When the MAIN POWER switch is set to ON and POWER ON or POWER SOURCE ON/OFF button of the remote controller or the sub power button on the main unit located at the front part of the bottom plate is on. Lights or blinks green On When the indicating lamp blinks in green or the message "POWER SAVE" or "OUT OF FREQUENCY" appears on the screen, there is something unusual about the status of reception. See "Symptoms That Seemingly Appear to be Failures. " 22 SUB-POWER ON Main power switch POWER SOURCE ON/OFF OFF Main unit Remote controller TIPS Avoid repeatedly turning the monitor on and off at short time intervals. s Turn off the main power switch ( ) before leaving the monitor out of use for an extended period of time. s If a power failure occurs while the main unit is running, it would be powered on upon recovery from the failure. Turn off the unit main power switch before leaving the main unit. s 9 ENGLISH q To turn on the main unit power supply, main unit the MAIN POWER switch ( ) of the main OPERATING INSTRUCTIONS (continued) Press the TV button to display "TV" in the LCD. The remote controller is functional only when "TV" is displayed in the LCD. If "TV" is not displayed in the LCD, press the TV button. ENGLISH 10 Input Selection q Turn the remote controller jog dial to choose an input signal (VIDEO1, VIDEO2, RGB1, or RGB2) and press the ENT button. Turn the remote controller jog dial to choose INPUT and press the ENT button, or press the main unit RGB/VIDEO button to switch through VIDEO1, VIDEO2, RGB1, and RGB2 in this order. s When the same signal is input to RGB1 and RGB2, the phase may in some cases shift slightly but this is not a malfunction. In such case, readjust the PHASE of the one being used. ENT Remote controller VIDEO1 (composite or S input) VIDEO2 (COMPONENT input) TV VID- I 1 RGB1 RGB2 (D-sub input) (BNC input) ENT Main unit RGB/VIDEO Volume Adjustment q While the on-screen display system is not on display, press the remote controller VOLUME button (VOL) v or w (or the main unit VOLUME button v or w) to adjust the sound volume. s The adjustment status will be displayed as guidance while you press these buttons. q While the guidance is on display, press v to turn up R e m o te c o n tr o lle r VOL Sound volume setting the volume. s You can also adjust the sound volume setting via the on-screen display system. [. . . ] Please note that this is not a malfunction. The plasma display panel is lighting the contents. phosphors by the discharge of internal radiation. Depending on the screen contents, in rare cases this may cause vertical stripes to appear because of failure to light. Please note that this is not a malfunction. A visual illusion may cause it. Adjusting the q Coarse horizontal stripes appear in FULL display. ( durning personal computer signal input) phase will reduce the horizontal stripes. 23 ENGLISH computer is lower than 75Hz, try increasing the frequency (upper limit: 75Hz). [. . . ]