User manual MARANTZ PM-11S2

[. . . ] Model PM-11S2 User Guide Integrated Amplifier CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPON-DANTE DE LA PRISE ET POUSSER JUSQU'AU FOND. IMPORTANT SAFETY INSTRUCTIONS READ BEFORE OPERATING EQUIPMENT This product was designed and manufactured to meet strict quality and safety standards. There are, however, some installation and operation precautions which you should be particularly aware of. [. . . ] · If using 2 sets of speakers, total speaker impedance must be 8 or more. Set to "STEREO" 3 2 1 2 3 1 AC IN To LINE IN jacks Active subwoofer, etc. L CH speaker R CH speaker 12 ENGLISH WIRING SPEAKER CABLE · Peel off the coating of speaker cable as shown below. Approx. Plug the supplied AC power cable to the AC IN socket on the rear panel of the main unit. Cut the coating of cable. Peel off the edge of cable. Twist conductors. AC IN · Wiring with speaker cable. Turn counterclockwise to loosen. Insert conductor of cable. Turn clockwise to tighten. 2. Plug the power cable into an AC outlet. Connect the player so that the power cord can be removed easily as a precaution against possible accidents. · Wiring with "Y" style terminal Turn counterclockwise to loosen. Insert conductor. Turn clockwise to tighten. Notes: · To prevent damage to circuitry, do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. · Do not touch the speaker terminals when the power is on. · Be sure to connect the positive and negative cables for the speaker properly. If they are miss-connected, the signal phase will be reversed and the signal quality will be corrupted. 13 OTHERS TROUBLESHOOTING ADVANCED OPERATIONS ADVANCED CONNECTIONS BASIC OPERATIONS BASIC CONNECTIONS NAMES AND FUNCTIONS BASIC CONNECTIONS ENGLISH BASIC OPERATIONS PLAYBACK To explain how to play back input sources, representative examples are given with an Super Audio CD player and analog record player. Before starting either procedure, check the component is correctly connected to the PM-11S2. NAMES AND FUNCTIONS BASIC CONNECTIONS BASIC OPERATIONS ADVANCED CONNECTIONS ADVANCED OPERATIONS TROUBLESHOOTING OTHERS 6. Adjust the volume level from the VOLUME knob !0 on the PM-11S2 or the VOLUME 3/4 buttons n of the remote controller. 7. Adjust bass/treble as desired from the TONE button e on the PM-11S2 or the TONE button v of the remote controller. For instructions on how to adjust bass and treble, see "How to Trim Bass" and "How to Trim Treble" on pg. Press the power ON/OFF switch of the Super Audio CD player to activate power to it. 8. You can turn the display and side illumination ON/OFF as suited for the room environment. Press the DISPLAY button w on the PM-11S2 or the DISPLAY button m of the remote controller. 2. Press the POWER ON/OFF switch !3 of the PM-11S2 to activate power to it. When using multiple PM-11S2s connected by F. C. B. S. , turn power ON in the order of lowest to highest ID number, starting from ID 1. 3. Select the input source from the INPUT SELECTOR knob q on the PM-11S2 or the input selector buttons z of the remote controller. q wer o !0 4. To use the speakers connected to the SPEAKER A terminals, press the SPEAKER A button r on the PM11S2. DISPLAY ATT. TONE PRE OUT 5. Load a disc into the Super Audio CD player and press the play button to start playback. SPEAKER A OPERATE REC OUT INPUT SELECTOR VOLUME POWER ON/OFF 6. Adjust the volume level from the VOLUME knob !0 on the PM-11S2 or the VOLUME 3/4 buttons n of the remote controller. SPEAKER B PHONES PHONO MC !3 7. Adjust bass/treble as desired from the TONE button e on the PM-11S2 or the TONE button v of the remote controller. For instructions on how to adjust bass and treble, see "How to Trim Bass" and "How to Trim Treble" on pg. You can turn the display and side illumination ON/OFF as RECORDER 1 LINE 1 suited for the room environment. Press the DISPLAY button w on the PM-11S2 or the DISPLAY button m of the remote controller. RECORDER 2 LINE 2 TRIM EXIT TONE + 7 Disc Playback on an Analog Record Player 1. [. . . ] connected. ¶ If excessive ultrabass signals are input The protection circuit is also activated if ultrabass signals are input. In such a case, the OPERATE indicator flashes, and the volume is automatically reduced. If excessive ultrabass signal input continues or if DC voltage is detected owing to trouble with the amplifier, the amplifier shuts itself OFF, and the OPERATE indicator flashes. To deactivate the protection circuit, turn the unit off then back on again after about 1 minute or more. ¶ If the main-amplifier overheats The protection circuit is activated if the temperature of the mainamplifier section rises above a certain level, which can happen if the amplifier is continuously used with excessive signal flow being input to it. [. . . ]