User manual MARANTZ PM-90SE

[. . . ] ONLY This undertaking is in addition to a consumer's statutory rights and does not affect those rights in any way. ITALIANO GARANZIA L'apparecchio è coperto da una garanzia di buon funzionamento della durata di un anno, o del periodo previsto dalla legge, a partire dalla data di acquisto comprovata da un documento attestante il nominativo del Rivenditore e la data di vendita. La garanzia sarà prestata con la sostituzione o la riparazione gratuita delle parti difettose. Non sono coperti da garanzia difetti derivanti da uso improprio, errata installazione, manutenzione effettuata da personale non autorizzato o, comunque, da circostanze che non possano riferirsi a difetti di funzionamento dell'apparecchio. Sono inoltre esclusi dalla garanzia gli interventi inerenti l'installazione e l'allacciamento agli impianti di alimentazione. [. . . ] Attenuation level is set to ­20 dB when the PM-90SE is shipped from the factory, but it can be set to either ­40 dB or - (mute). For instructions on how to set attenuation level, see "How to Set Attenuation Level" on pg. 18. u DISPLAY Button This button turns the display and side illumination ON and OFF. The button performs two functions depending on how long it is pressed. If pressed and held for 3 seconds or longer: 10 NAMES AND FUNCTIONS OF PARTS !1 PRE OUT Button This button turns output from the PRE OUT jack on the rear panel ON and OFF. When output is ON, the center of the button is lit a blue color. !6 Display Panel Approximately 3 seconds after power to the PM-90SE is activated, the ID set for the PM-90SE is displayed here. After that, the top line displays the input source selected with either the INPUT SELECTOR knob or the remote controller, while the bottom line displays the volume level set with the VOLUME knob or the remote controller. When the PM-90SE I is first activated, the attenuation level (dB) is displayed for the initial volume level. Volume Level Indication Max !2 REC OUT Button This button turns the signals output from the RECORDER 1 and 2 OUT jacks on the rear panel ON and OFF. When RECORDER 1 is selected as the input source, signals are not output to the RECORDER 1 OUT jack. The same goes for the RECORDER 2 OUT jack when RECORDER 2 is selected as the input source. !3 PHONO MC Button This button switches the phono equalizer between MC and MM. In the bi-amp mode, the R channel jack cannot be used. E LINE 1/2 Input Jacks These jacks are for connecting to the output jacks of a tuner, DVD player, etc. In the bi-amp mode, the R channel jack cannot be used. K Operating Mode Switch This switch is for setting the operating mode of the PM11S1. STEREO: Set to use the PM-90SE as an ordinary 2-channel stereo amplifier. BI-AMP: Set to use two PM-90SEs in a complete bi-amp connection with FCBS. For more information on the bi-amp mode, see "ABOUT THE BI-AMP MODE" on pg. 17. F RECORDER 1/2 IN Jacks These jacks are for connecting to the output jacks of a CDR, MD deck, tape deck, etc. In the bi-amp mode, the R channel jack cannot be used. G RECORDER 1/2 OUT Jacks These jacks are for connecting to the recording input jacks of a CD-R, MD deck, tape deck, etc. Output signals can be turned ON/OFF from the REC OUT button on the front panel. In the bi-amp mode, the signals input to the L channel are output to both output jacks. L AC IN Socket Connect one end of the included power cable here and the other end to a power outlet. The PM-90SE can be powered by 230V AC only. 12 NAMES AND FUNCTIONS OF PARTS RC-11PMS1 REMOTE CONTROLLER This remote controller can control the PM-90SE and Marantz Super Audio CD players and DVD players that have a remote control receptor. The operations possible by remote control may differ with each component, therefore see the instruction manual that came with the component. [. . . ] If the equipment becomes heavily soiled: · dilute some washing up liquid in water, in a ratio of one part detergent to six parts water. · dip a soft, lint free in the solution and wring the it is damp. · dry the equipment by wiping it with a dry cloth. 23 ENGLISH SPECIFICATIONS & DIMENSIONAL DRAWINGS ENGLISH Power output (20 Hz ­ 20 kHz simultaneous drive of both channels) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100W x 2 (8 load) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]