User manual MARANTZ PM7200

[. . . ] Model PM7200 User Guide Integrated Amplifier Page 4 03. 12. 17, 11:19 AM CONTENTS Engligh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1 Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 35 Page 6 03. 12. 17, 11:19 AM CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. [. . . ] When SOURCE DIRECT is turned on, the audio signal path is as short and direct as possible in order to enjoy high-quality sources under the best conditions possible. NOTE: Tape and CD-R/MD playback and recording are not possible when the SOURCE DIRECT switch is on. Any graphic equalizer or other such component that is connected to the PROCESSOR IN/OUT jacks will not have any effect. In order to use any of these components or controls, it is necessary to turn the SOURCE DIRECT switch off. !1 POWER CORD Connect the power cord to a standard household power outlet. !2 POWER SWITCH Press this switch to turn power on (depressed) and off (raised). Note that the power of any equipment connected to the switched AC outlet on the rear panel (see !0 above) is also turned on and off by operating this switch. Turning on the power causes the POWER indicator to light, and the POWER indicator goes out when power is turned off. While the POWER switch is in the ON position (depressed), you can put use the remote control unit's SYSTEM POWER ON and OFF button to switch the amplifier between standby (indicated when the @6 STANDBY indicator is lit) and power on. @2 BASS AND TREBLE TONE CONTROLS Use these controls to control the levels of their corresponding frequency bands. TREBLE adjusts the high frequency band, while BASS adjusts the low frequency band. Rotating a control towards (+) enhance the frequency band, while rotating towards () attenuates the frequency band. 2 Page 2 03. 12. 17, 11:18 AM @3 CLASS A SWITCH Press this switch while amplifier power is turned off to switch between Class A (25W, 8 ohms) and Class AB (95W, 8 ohms) amplifier operation. The CLASS A indicator is lit while Class A operation is selected, and Class AB operation is indicated when the CLASS A indicator is not lit. OPERATION 1 INTEGRATED AMPLIFIER PM7200 3 VOLUME TAPE PHONO CD TUNER AUX1 AUX2 CD-R/MD INPUT SELECTOR TAPE MUTE CD-R/MD IMPORTANT: REC SELECTOR MIN MAX The top cover may become hot during Class A operation, but this does not indicate malfunction. Note, however, that you should never place anything on top of this amplifier. Doing so can block ventilation holes, resulting a build up of heat and malfunction of or damage to the amplifier. POWER ON/OFF PHONES STANDBY 1 SPEAKERS 2 OFF SOURCE TAPE CD-R BASS TREBLE CLASS A SOURCE DIRECT BALANCE CD-R TAPE COPY ON OFF - + - + ON OFF ON OFF L R 3 Perform the applicable operation on the connected equipment. @4 SPEAKER SWITCHES 1/2 Use these switches to turn speaker output on (depressed) and off (raised). You can turn off speaker output when listening to output over headphones. @5 PHONES JACK Use the jack to plug in headphones that are equipped with a standard phone jack. TO PLAY AN ANALOG RECORD 1. Use VOLUME to adjust volume, and BASS and TREBLE to adjust the tone. @6 STANDBY INDICATOR This indicator is lit while the amplifier is in the Standby Mode. Pressing the remote control unit's POWER buttons switches the amplifier between standby and power on. NOTE: Be sure the set VOLUME to is minimum setting before placing the stylus onto the record or before replacing the turntable's cartridge. Never subject the turntable to shock or vibration while a record is playing. Locating your turntable too close to the speakers can cause howling, which will make it impossible to use higher volume settings. Never turn off power while the stylus is in contact with the surface of the record. TO LISTEN TO AN FM/AM BROADCAST 1. Use VOLUME to adjust volume, and BASS and TREBLE to adjust the tone. TO PLAY A COMPACT DISC 1. Use VOLUME to adjust volume, and BASS and TREBLE to adjust the tone. TO PLAY EQUIPMENT CONNECTED TO THE AUX 1 OR AUX 2 JACKS 1. Use VOLUME to adjust volume, and BASS and TREBLE to adjust the tone. 3 Page 3 03. 12. 17, 11:18 AM DANSK SVENSKA PORTUGUS ITALIANO ESPAOL NEDERLANDS DEUTSCH FRANAIS ENGLISH FRANAIS DEUTSCH NEDERLANDS ESPAOL DANSK SVENSKA PORTUGUS ITALIANO ENGLISH TAPE DECK, CD-R/MD OPERATION USING THE REC SELECTOR Use the REC SELECTOR E to specify the type of recording you want to perform. INTEGRATED AMPLIFIER PM7200 INPUT SELECTOR VOLUME TAPE PHONO CD TUNER AUX1 AUX2 CD-R/MD TAPE MUTE CD-R/MD MIN MAX REC SELECTOR POWER ON/OFF PHONES STANDBY 1 SPEAKERS 2 OFF SOURCE TAPE CD-R BASS TREBLE CLASS A SOURCE DIRECT BALANCE CD-R TAPE COPY 1. Note that REC SELECTOR Eshould normally be in the OFF setting except when you are recording to tape. [. . . ] 0. 03% Damping factor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 Power output (classA operation) RMS 8 ohms (20 Hz-20 kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 W DIN 8 ohms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 W THD at 8 ohms RMS rated output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]