User manual MARANTZ PMD505

[. . . ] Model PMD505 User Guide Cassette Deck R IMPORTANT TO SAFETY WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. ¼ FOR U. S. A. & CANADA MODEL ONLY CAUTION TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. CAUTION: 1. Handle the power supply cord carefully Do not damage or deform the power supply cord. If it is damaged or deformed, it may cause electric shock or malfunction when used. [. . . ] Set the Function Selector or Tape Monitor switch on your amplifier or receiver to TAPE or Tape monitor position. The numbers in the illustration below depict the order in which operation steps are carried out. ENGLISH FRANÇAIS ESPAÑOL r e CASSETTE DECK PMD505 COUNTER RESET COUNTER RESET DOLBY NR C B OFF TIMER REC OFF PLAY REV. MODE SYNC REV DUBBING SPEED HIGH NORMAL REC LEVEL REC PAUSE REC MUTE AUTO REVERSE AUTO TAPE SELECT/HIGH SPEED DUBBING STOP PLAY STOP PLAY AUTO REVERSE AUTO TAPE SELECT/HIGH SPEED DUBBING CCONT. PLAY MIN EJECT POWER ON/OFF MAX PHONES EJECT PLAY A PITCH CONTROL ­ + B REC/PLAY t q uwy 6. When listening to a tape that has been recorded with Dolby noise reduction, set the DOLBY NR switch r to match the system used at the time of recording. DOLBY NR C B OFF 5. ¼ In the continuous playback mode (REV MODE set to ), playback of both tape sides will be repeated 5 times and then stop automatically. ¼ If different types of Dolby noise reduction are used for record and playback, playback response will be adversely effected. ¼ When power is turned off during tape transport, it may not be possible to remove the cassette by pressing the EJECT button. In this case, turn on power again before you press the EJECT button. Mode To listen to one side only To listen to playback of both sides To listen to continuous play back of both sides and both decks. Switch position RELAY PLAY (continuous playback of the tapes in deck A and deck B) ¼ Load a cassette tape into deck A and B, and set the Dolby NR button correctoly. w CASSETTE DECK PMD505 COUNTER RESET DOLBY NR C B OFF TIMER REC OFF PLAY REV. MODE SYNC REV DUBBING SPEED HIGH NORMAL COUNTER RESET REC LEVEL REC PAUSE REC MUTE AUTO REVERSE AUTO TAPE SELECT/HIGH SPEED DUBBING STOP PLAY STOP PLAY AUTO REVERSE AUTO TAPE SELECT/HIGH SPEED DUBBING CCONT. PLAY MIN EJECT POWER ON/OFF MAX PHONES EJECT PLAY A PITCH CONTROL ­ + B REC/PLAY q e ¼ Relay play will play deck A and B in succession for 5 times, upon which playback stops (Deck A Deck B Deck A Deck B Deck A) or (Deck B Deck A Deck B Deck A Deck B). 1. To stop relay play, press the STOP ( ) button e of the deck currently playing the tape. 4 RECORDING (DECK B only) ¼ Switch on your amplifier or receiver and the source component. ¼ Set the Function Selector and the REC Selector on your amplifier or receiver to the source to record, with Tape Monitor switch (it available) set to monitor e CASSETTE DECK PMD505 COUNTER RESET DOLBY NR C B OFF TIMER REC OFF PLAY REV. MODE SYNC REV !0 ot COUNTER RESET REC LEVEL REC PAUSE REC MUTE AUTO REVERSE AUTO TAPE SELECT/HIGH SPEED DUBBING STOP PLAY STOP PLAY AUTO REVERSE AUTO TAPE SELECT/HIGH SPEED DUBBING CCONT. PLAY MIN EJECT POWER ON/OFF MAX PHONES EJECT PLAY A PITCH CONTROL ­ + B REC/PLAY 1. (Check that the erasure prevention tabs of the cassette housing have not been broken off. ) 3. Move the DOLBY NR switch e and select the Dolby NR type that suits the recording. DOLBY NR C B OFF 5. Adjust the recording level with the REC LEVEL control y while watching the Peak Level Meter. Press the PLAY ( ) button u or PAUSE ( ) button o to resume recording. Caution: ¼ Be careful not to erase important recordings by mistake. If the PLAY button is pressed while the REC indicator lights, recording starts. If the PLAY and REC ( ) button are pressed at the same time, recording starts. [. . . ] Adjust recording input level. High frequency range (treble) is emphasized. High frequency range (treble) is lost. ¼ Dolby NR switch is set improperly. ¼ If the POWER switch is turned off in either during recording or playback and the unit is stopped, there may be case when the cassette cannot be removed, even if the ( EJECT) button is pressed. ¼ Set Dolby NR switch properly. ¼ Turn the POWER switch ON ( ) again, and then press the STOP ( ) button. [. . . ]