User manual MARANTZ PS-17

[. . . ] R Model PS-17 User Guide AV Amplifier ENGLISH WARRANTY For warranty information, contact your local Marantz distributor. RETAIN YOUR PURCHASE RECEIPT Your purchase receipt is your permanent record of a valuable purchase. It should be kept in a safe place to be referred to as necessary for insurance purposes or when corresponding with Marantz. IMPORTANT When seeking warranty service, it is the responsibility of the consumer to establish proof and date of purchase. Your purchase receipt or invoice is adequate for such proof. Non sono coperti da garanzia difetti derivanti da uso improprio, errata installazione, manutenzione effettuata da personale non autorizzato o, comunque, da circostanze che non possano riferirsi a difetti di funzionamento dell'apparecchio. [. . . ] Press the remote control unit's <, >, ^, v cursor button or the OK button. Press the < or > cursor button to select the SYSTEM SETUP item on the OSD MAIN MENU, and press the OK button to enter the selection. OSD MA I N ME NU Example 1: Digital recording onto an MD from CD:DIG. 4 while playing and listening to a DVD using the DVD:DIG. 5 input (The digital signals have already been connected as in the connection example. ) 1. Proceed with the steps for "Preparations for recording using digital signals, " and select DIG. 4. The COPY indicator now lights. SYSTEM SETUP 1/2 ENGLISH MA I N IN SW : : : COUPL ED 6ch D I G4 6 CH - I NPUT D IGITAL OUT SURROUND CHANNEL SYSTEM SPEAKR MODE LEVEL OSD I NFO : : ENABL E D ISABLE S. P. C. SETUP SETUP RETURN NEXT EX IT EX IT 4. Press the ^ or v cursor button to move to the DIGITAL OUT item. SYSTEM SETUP 1/2 MA I N IN SW : : : COUPL ED 6ch SOURCE 6 CH - I NPUT D IGITAL OUT 3. OSD I NFO : : ENABL E D ISABLE 4. S. P. C. Set the digital input for the MD player, and set the player to a recording standby status (such as synchro REC). Recording now starts. RETURN NEXT EX IT OTHER FUNCTIONS 5. n The status changes in the following sequence: SOURCE OFF DIGITAL 1 DIGITAL 6 DIGITAL 2 DIGITAL 5 DIGITAL 3 DIGITAL 4 SETTING THE SLEEP TIMER (ONLY REMOTE CONTROL UNIT) Set the sleep timer while the power is turned on. Press the SLEEP button /7 the number of times to set the desired sleep time. Each press of the SLEEP button /7 changes the display in the following order: 10 OFF 20 90 30 80 40 70 50 60 6. n When SOURCE is selected, the input signals from the component selected by the function button are output. The selected input will not be output unless the digital signal input has been set. n It is recommended that OFF be selected as the setting if no component has been connected to the DIGITAL OUT jacks. Press the OK button to return to the regular display. "SLEEP" stops blinking and lights steadily. While the sleep timer is activated, the remaining time can be displayed for approx. To cancel the sleep timer, press the SLEEPbutton /7 and then press the CLEAR button. 16 SURROUND MODES Surroud mode AUTO FEATURES When this mode is selected, the receiver determines whether the digital input signal is Dolby Digital, PCM-audio or DTS. Note: When a Dolby Digital or DTS signal is input, the number of channels for which the corresponding signal is encoded will be played. Inputting a Dolby Digital two channel signal with Dolby surround status automatically subjects that signal to Pro-Logic processing before play. Dolby Virtual surround sound playback is initiated automatically if 5. 1-channel signals or Dolby Surround signals are input when the setting does not call for the surround speakers to be used. With a setting which does not call for the surround speakers to be used, Dolby Virtual surround sound playback is initiated. Using only the front left and right speakers, virtual surround sound playback results to give the impression that surround speakers are present. (Note: The effect will differ depending on the playback source and viewing/listening position. ) With a setting which calls for the surround speakers to be used, the Dolby Digital 5. 1-channel signal input is played back as is. On the other hand, 2-channel input signals (both analog and digital) are subject to Dolby Pro Logic processing and played back. Note: Playback is not initiated for DTS input signals or 96 kHz PCM input signals. Stereo program sources the left and right channels play normaly when PCM-audio or analog stereo is input. [. . . ] Remember that the procedure will reset the settings of the function selector, Surround mode, delay time, etc. , to their initial settings. TECHNICAL SPECIFICATIONS POWER AMP SECTION Rated Power Output (20 Hz to 20 kHz, 2 ch simultaneous drive) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 W·2 (8 W load) 80 W·2 (6 W load) 100 W·2 (4 W load) AUDIO SECTION Total harmonic distortion (20 Hz to 20 kHz, 2 ch drive, 8 W load) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 01 % Cross-modulation distortion (SMPTE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 01 % Output bandwidth (8 W load, 0. 04 %) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]