User manual MARANTZ RC-1200

[. . . ] R Model RC1200 User Guide Learning Remote Control LOADING BATTERIES . . . . . . . . . . . . . . . . . . . . . . . . . . 9 USE MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 MAIN FEATURES & FUNCTIONS ENGLISH · PROGRAMMABLE LEARNING FUNCTION Can easily be programmed to learn the codes for almost any other infrared-based remote, allowing the remote control functions for many different components to be consolidated conveniently in a single unit. [. . . ] Once the data is cleared, the codes are either returned to their original display or left empty. · To cancel the memory clearing operation, do not press the OK Cursor button /0 and simply touch any other button. After the OK Cursor button /0 is pressed, clearing the entire memory will take approximately 10 seconds. ENGLISH 1. PROGRAMMING MACROS Macros make it possible to use a single function button to perform more complex series of operations that would normally require pressing several buttons. A single button can be programmed to perform up to 10 steps in sequence. A typical example of such a series might be as follows: · Turn the main amplifier power ON Switch the function to DVD Set the Surround Mode to Pro Logic Switch the TV to video input Set the DVD player to PLAY. · The various steps that make up a macro are set initially to be sent one after another in 1 second intervals, however these intervals may be shortened to as little as 0. 5 seconds or lengthened to as much as 5 seconds using the Setup mode. · In the macro mode, the number of steps the macro contains is displayed on LCD c. Macros may be programmed for each of the 11 function buttons, from LD to AMP. Use a ballpoint pen or other sharp point to press the MACRO button x until the MACRO and LEARN indicators are displayed blinking on the LCD. POWER SOURCE ON ON / OFF OFF LEARNING REMOTE CONTROL RC 1200 MACRO MODE 2. Example The LCD A will display LD-M. The characters displayed at LCD A are as follows. However, when a function name has been overwritten, "­M" appears for the first 2 or 3 characters. LD-M, DVD-M, TV-M, DSS-M, VCR-M, AUX-M, TUN-M, CD-M, TP-M, AMP-M, CDR-M (or MD-M for remote controller set for MD). · If a macro has already been set for the selected function button, the LCD A will blink. Press the buttons for the operations you wish to program as a macro in the sequence you want the macro to program them. The number of steps in the macro is displayed on LCD C and this number increases by 1 with each button pressed. For example, press LD, PLAY. ENT EN w CH OK VO CD DSS TV DVD VCR TAPE CD-R/MD AUX AMP MUTE HALL q LD CLEAR AUTO TUNER MEMO DOLBY THX GUIDE DTS Each function button can be programmed to perform up to 10 steps in sequence. ENGLISH Press the Function button , for which you wish to program a series of operations. Press the LD Function button , . · If, while programming, no buttons are pressed for approximately 1 minute, the remote controller will automatically return to normal mode, and no macro will be programmed in the memory. When you are finished programming macros, use a ballpoint pen or other sharp point to press the MACRO button x. · Macros cannot be programmed for the MODE z, MACRO x, < · 3 /1, VOL / . , MEMO /6 or CLEAR /5 buttons. Although function operations in the Macro Mode can be programmed more than once, only the first function memorized in the ten function buttons including LD, CD, TV--but not the AMP button--will be sent from the remote controller (the amplifier or receiver function will change). For this reason, it is not possible to select multiple amplifier functions in a macro button. (If the AMP button is programmed, the same operations as those in the other function buttons will be performed. ) Therefore, when executing operations in the Macro Mode, what happens is that, starting with the second function operation, only the function mode of the remote controller is changed, and no signals are sent. ENGLISH EDITING MACROS Macros may be edited using following procedure. Use a ballpoint pen or other sharp point to press the MACRO button x until the MACRO and LEARN indicators are displayed blinking on the LCD. [. . . ] One square (7) in LCD c is equivalent to an interval of 0. 5 seconds, allowing intervals of up to 5 seconds to be set. The remote controller is set at the factory with an interval of 1 second, as indicated by (77&&&&&&&&). Adjust the interval between transmission of operation codes using the < and > Cursor buttons /0 , then press the OK Cursor button /0. ENGLISH · To cancel the setting, press any button other than the Cursor button /0. Every 7 at LCD C represents a second, and a lighting duration of up to 10 seconds can be set. [. . . ]