User manual MARANTZ RC3001

[. . . ] 31 1:03:54 PM For US and Canada Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] 31 1:04:40 PM Notes: • When affixing the IR emitter, be sure to affix it in front of the IR receiver of the equipment to which it will be connected. €¢ Do not connect a commercial dual IR emitter to the IR output jack. iR RF RC3001 Remote controller RX3001 1 2 3 4 5 6 Set top box CD Changer 1 2 3 4 5 OPEN/CLOSE PLAY STOP PAUSE 1 2 3 4 5 DISC LR MP3 CD HD CD PROGRAM TRACK SUPER VCD DVD AC - 3 SURR ECHO RANDOM REPEAT 1DISC A-B INTRO SPACE PBC SLOW STEP RESUME NTSC PAL MIN TOTAL EACH REMAIN SEC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 PHONES IR Emitter cable VCR TV DVD recorder STANDBY FL OFF Amplifier 3. CONNECTING TO AN AC ADAPTER Connect the supplied AC adapter to the DC jack. CONNECTING TO NON-MARANTZ EQUIPMENT SETUP SETTING THE IR OUTPUT LEVEL The DIP switches at the bottom of the RX3001 can be used to set the IR output levels from IR output jacks 1 to 3 and IR output jacks 4 to 6. Note: The default setting is high output (LEVEL 4), and so when the IR emitter is affixed to a device, the output level can be so high that remote commands cannot be controlled properly. Be sure to set the IR output level according to the status of the connected device. ON OFF 1 2 3 4 1 2 OUT6 6 LEVEL 1 2 3 4 OUTPUT 4+5+6 SW 1 OFF OFF ON ON SW 2 OFF ON OFF ON OUTPUT 1+2+3 SW 3 OFF OFF ON ON SW 4 OFF ON OFF ON SETTING THE CHANNEL Use the CH selector knob to set to the same channel as the RC3001. ON OFF 1 2 3 4 ID 1 2 CH selector knob Notes: • When setting the channel with the CH selector, the available channels are CH1 to CH4 with two setting positions for each channel. cH1 CH2 CH3 CH4 • The RC3001 default channel is channel 1. €¢ To change the channel of the remote controller, change the channel setting in the Wizz. If a different ID signal is sent from the remote controller, no control signal is output from the RX3001. Group ID Receiver side Emitter Output 1 2 3 4 5 6 Receiver side Emitter Output 1 2 3 4 5 6 1 Set ID 1 Set ID 1 Set ID 1 Set ID 1 Set ID 1 Set ID 1 ID 1 2 Group ID 2 Set ID 1 Set ID 1 Set ID 1 Set ID 2 Set ID 2 Set ID 2 Output from the Output jack is controlled as shown below based on the remote device ID setting and receiver ID setting. It 3 editor software can be used to make the settings for the IR Command, LINK, JUMP, One Touch Operation (Macro) and other functions in the RC3001. This enables a customized user interface, optimized for the customer s environment, to be built. For more information about the setting procedures, see the PC Editor Software Wizz. SLEEP TIMER The SLEEP TIMER is a function that sends a preset remote command after the sleep time has elapsed. It 3 editor, and the buttons that are assigned to the sleep timer are operated as shown below. €¢ This is a convenient function for devices that do not have a sleep timer or for setting the sleep timer using multiple devices. Each time the button is pressed, the sleep setting time changes in the cycle shown below. Perform operation of the device that you want to control in the selected device mode. To control another device, return to Home mode and select another device. [. . . ] Press the button next to the NO (Disable) or YES (Enable) indicators on the LCD to either enable or disable initialization. €¢ Either press the ENTER button or wait three seconds for the LCD to automatically return to the SYS. €¢ Pressing the Home button returns the LCD to the MAIN MENU. Pressing the YES button displays COMPLETED on the LCD and completes initialization. [. . . ]