User manual MARANTZ SA-15S1

[. . . ] Model SA-15S1 User Guide Super Audio CD Player CLASS 1 LASER PRODUCT LUOKAN 1 LASERLAITE KLASS 1 LASERAPPARAT CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPON-DANTE DE LA PRISE ET POUSSER JUSQU'AU FOND. LASER SAFETY This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to possible eye injury. CAUTION : USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURE OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. IMPORTANT SAFETY INSTRUCTIONS READ BEFORE OPERATING EQUIPMENT This product was designed and manufactured to meet strict quality and safety standards. There are, however, some installation and operation precautions which you should be particularly aware of. [. . . ] (See page 16) <0 DIGITAL OUT button This button is pressed to turn the digital output for the Audio CD signal on and off. (See page 13) ¤4 A-B (A-B Repeat button) This button is to determine starting and ending points for A-B repeat play. (See page 14) <1 INPUT button This button switches the input selector (INPUT) of the Marantz PM-15S1 amplifier. ¤5 RANDOM button <2 VOLUME button This button is for random play. (See page 15) This button is used to increase or decrease the volume of the Marantz PM-15S1 amplifier. ¤6 AMS (Automatic Music Scan button) Use this button for AMS play. (See page 16) ¤7 REPEAT button This button is for repeat play. "All Repeat" "Track Repeat" "Repeat Off" (See page 14) ¤8 MENU button and ENTER button (Menu setup) These buttons are used to set the time for quick replay. (See page 17) ¤9 QUICK REPLAY (Quick replay) button This button is used to do quick replay of the tracks. (See page 17) 7 ENGLISH NAMES AND FUNCTIONS NAMES AND FUNCTIONS ENGLISH REAR PANEL A ANALOG OUTPUTS connectors These are the output jacks of the analog audio signals. The supplied analog connection cord can be connected to the CD, AUX, or other connectors on an amplifier. Be sure to connect the L and R channels correctly to the corresponding jacks. * Never connect to the PHONO connector on the amplifier. D REMOTE CONTROL IN, OUT (input and output) connectors When the remote control connectors on the player and on a Marantz AV component are connected using the accessory remote control connecting cables, the components can be operated as a system by remote control. · When connecting to a component which is equipped with remote control connectors, the player's REMOTE CONTROL IN connector must always be connected to the REMOTE CONTROL OUT connector on the other component to be connected. When connecting a component which is not equipped with an infrared remote sensor, this component must always be connected to the player's REMOTE CONTROL OUT connector. B DIGITAL AUDIO OUT COAX. It outputs the playing Audio CD signal in digital format. This jack is to be connected with a recording device, amplifier, D/A converter, etc that has coaxial digital input using an optional coaxial digital cable. * No signal will be output when a Super Audio CD is played. · C DIGITAL AUDIO OUT OPT. It outputs the playing Audio CD signal in digital format. This jack is to be connected with a recording device, amplifier, D/A converter, etc that has optical digital input using an optional square type optical digital cable. * No signal will be output when a Super Audio CD is played. E EXT. /INT. (Ext. /Internal switch) When this unit is used as a standalone component, set this switch to the INT. When it is used connected to external component by a remote connecting cable and to audio component with a remote sensor that supports remote controls by Maranz, set this switch to the EXT. position, remote control unit cannot be used. F AC POWER INPUT JACK Connect the supplied power cord to this jack and a household AC power outlet. 8 DISPLAY c d e f gh i j k l m n a b a Main display The time display and text information of the disc to be played as well as the setting menus and other displays appear on the main display. h PROG (program) indicator This lights during program play. i RNDM (random) indicator This lights during random play. b 1-20, (music calendar) The number of tracks recorded on the disc to be played, the number of remaining tracks to be played, and the number of tracks programmed by program play appear here. " " light when 21 or more tracks have been recorded on the disc. j AMS (auto music search) indicator This lights during AMS playback. k CD, SUPER AUDIO CD, STEREO Disc indicator This indicates the type of disc on the disc tray. c 3 (play) indicator This lights during disc play. l TOTAL (total time) indicator d 8 (pause) indicator This lights when play is paused (temporarily stopped). When the total remaining time or the total program time is displayed, this lights above the display. e , ALL, 1 (repeat) indicator This lights during repeat play. m REMAIN (remaining time) indicator When the remaining playback time of a track is displayed, this lights above the display. f A-B (A-B repeat) indicator This lights during A-B repeat play. n D OFF (digital output off) indicator This lights when the digital output setting for the CD signal is set to off. [. . . ] This is not a problem with this unit. The disc is rotating but no sound is heard. Is the amplifier's function or selector switch set to "CD" or "AUX" or such (to whatever you have connected this unit to)?* In the case of a CD-R or CD-RW disc, this problem may occur when the conditions under which its data was originally written were substandard or when the quality of the disc itself is poor. * This condition may occur in Mixed-Mode CDs, CD Extra, and other discs that have CDDA format mixed with other data. [. . . ]