User manual MARANTZ SD 8020 SERVICE MANUAL
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual MARANTZ SD 8020. We hope that this MARANTZ SD 8020 user guide will be useful to you.
Manual abstract: user guide MARANTZ SD 8020SERVICE MANUAL
Detailed instructions for use are in the User's Guide.
[. . . ] The files of Wizz. it 3 are automatically placed in a separate directory.
CUSTOMIZING THE CONFIGURATION FILE
During the installation of the editor, one configuration file was also saved on your PC. There is one default configuration file which you can start from to create a custom configuration file (CF) (defaultRC3001. mcf). The default CF is constructed in such a way that they can be easily adjusted to the needs of every customer. • This file contains the main Marantz remote control codes for enabling control of Marantz products with the default settings.
CONNECTIONS
CONNECT PC AND REMOTE CONTROLLER
1. [. . . ] Select the automatic scanning of USB driver or select the location of USB driver. The location of RC2001_3001 USB driver C:\Program Files\Marantz\Marantz Wizz. it 3
Note: The USB driver of RC2001 and RC3001 does not take the certification of Microsoft. However, you can use it in your PC.
2
RC3001_E_Wizzit3_ENG. indd 2
07. 9. 3 1:38:29 PM
WIZZ. IT 3 OPERATION
After Wizz. it 3 is installed, the Wizz. it 3 icon is displayed on the PC desktop. To make settings for the remote controller after startup, either edit the default configuration file or use a new configuration file.
ICON DESCRIPTIONS
q
w
e
r t
y
u
i
o
!0
!1
!2 !3
!4
!5
!6
!7
!8
q New Configuration This creates a new setting configuration. e Save Configuration This saves the configuration that is being edited as a user file to the PC. r Download to remote control This writes the edited configuration to the remote controller. t Upload from remote control This loads remote controller settings to the PC. u Redo This is used to redo an edit operation in the settings that were undone. !0 Paste This pastes a selected setting.
!1 Delete This deletes a selected setting. !2 Label This is used to set the label of a selected device or button. !3 Properties This is used to set the properties of a selected device or button. Specify the file saved in the PC to load the IR codes registered in My Database. e IR Database This loads and sets the IR codes from the IR Database containing the remote codes from various brands. (Refer to page 8, IR Database Window . ) r RC5/6 This uses direct key input to set the remote control codes RC-5, RC-5 Extension, RC-6 mode 0, RC-6 mode 6A used by Marantz. (Refer to page 9, Edit RC5/RC6 Window (Direct Input Code . ) t Test IR This performs a test transmission of IR commands by sending a preset code from the remote controller connected to the PC. y Duration This is used to adjust the duration of the IR command.
6
RC3001_E_Wizzit3_ENG. indd 6
07. 9. 3 1:38:30 PM
LEARN IR
1.
Use a USB cable to connect the PC making the settings to the remote controller (RC3001/ RC2001).
2. 5.
Place the remote controller so that its infrared signal transmitter is facing the infrared signal receiver on the remote controller at a distance of about 2 inches (0. 05 m). Learning is complete when LEARN OK is displayed in Results.
7
RC3001_E_Wizzit3_ENG. indd 7
07. 9. 3 1:38:30 PM
IR DATABASE WINDOW
q
w r e
t
q Brand Select the brand name of the device to be controlled. e Model Number Select the model number of the device to be controlled. r Functions Select from the displayed remote control codes registered for the selected model number. t Test IR This performs a test transmission of IR commands by sending a preset code from the remote controller connected to the PC.
8
RC3001_E_Wizzit3_ENG. indd 8
07. 9. 3 1:38:31 PM
EDIT RC5/RC6 WINDOW(DIRECT INPUT CODE)
Use the radio buttons to select the code type that will be set. After entering the codes, click OK.
9
RC3001_E_Wizzit3_ENG. indd 9
07. 9. 3 1:38:31 PM
CREATE LINK WINDOW
To set a link, select the action list that will be linked to by clicking the Device name → Hard button or Page → Button label name. [. . . ] After entering the codes, click OK.
9
RC3001_E_Wizzit3_ENG. indd 9
07. 9. 3 1:38:31 PM
CREATE LINK WINDOW
To set a link, select the action list that will be linked to by clicking the Device name → Hard button or Page → Button label name. After determining the link, click OK.
10
RC3001_E_Wizzit3_ENG. indd 10
07. 9. 3 1:38:31 PM
CREATE JUMP WINDOW
Make the setting by selecting the device name and the page number where the jump operation will go to. After determining the jump locations, click OK.
ADD BEEP WINDOW
This is used to set the beep sound frequency and duration. After making the settings, click OK.
11
RC3001_E_Wizzit3_ENG. indd 11
07. 9. 3 1:38:31 PM
LABEL WINDOW
t
q
w e r
Key Area
This is used to set the command name displayed on the remote controller LCD. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE MARANTZ SD 8020
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual MARANTZ SD 8020 will begin.