User manual MARANTZ SR 7200

[. . . ] RETAIN YOUR PURCHASE RECEIPT Your purchase receipt is your permanent record of a valuable purchase. It should be kept in a safe place to be referred to as necessary for insurance purposes or when corresponding with Marantz. IMPORTANT When seeking warranty service, it is the responsibility of the consumer to establish proof and date of purchase. ONLY This undertaking is in addition to a consumer's statutory rights and does not affect those rights in any way. [. . . ] The unit enters multi room mode and the display indicates “SEL SOURCE” and flashes the “MULTI ROOM” indicator for approx. In this time, you can select the input source by pressing the FUNCTION SELECTOR button t. At this time, you can set the volume level of the multi room by turning the volume control knob. At this time, you can set PAL or NTSC for second zone TV format of OSD. Then, the display indicates “M/SLEEP OFF” and you can set sleep timer for multi room by pressing by the SLEEP button o. GENERAL INFORMATION When the OSD button ⁄7 is pressed, the current setting are displayed on the TV monitor. This display disappears automatically in about 5 seconds after the button is pressed. Note: If the multi room function is to be set using the remote control unit, select the settings on the MULTI ROOM SETUP screen in the OSD MAIN MENU. If Video output for multi room is connected to the TV in your second zone, the on screen display for this video signal will be shown as follow. Q VIDEO SOURCE: Displays the current video source being selected with the function selector TV, DVD, VCR1, DSS or AUX. W AUDIO SOURCE: Displays the current audio source being selected with the function selector FM, AM (MW, LW), CD, TAPE, CD-R, TV, DVD, VCR1, DSS or AUX. E DIGITAL INPUT: Displays the digital input that you are using DIG-1, DIG-2, DIG-3, DIG-4 or DIG-5. Press the POWER ON button, or select the desired source on multi room remote control unit from the MULTI ROOM. Any of these operations will put the SR7200 into multi room mode and “MULTI ROOM” indicator will light and OSD system for the TV in the multi room will be shown. DOWN button on the multi room remote control unit to set the desired sound volume. In multi room mode, the multi room remote control unit can be used in the multi room to operate the following functions. You can select a tuner preset channel and tuning up or down, and direct selection. And you can control the CD player, DVD player VCR and tape deck connected to the SR7200. Additionally, SLEEP timer function for multi room is available from second zone, by pressing the SLEEP button on the multi room remote control unit. The status of the main room setting can be monitored from the second zone with the OSD. 1 CH SURR, PLO LOGIC, PLII MUSIC, PLII MOVIE, DTS t MULTI ROOM Displays the current status of the Multi Room function, ON or OFF. Note: The On-Screen Display signals for the main room can be output from the TV MONI composite video (RCA) output and the TV MONI, S-Video and TV MONI component video output jacks. [. . . ] Status L, C, R, SL, SR, LFE L, R L, R, SC L, R L, R L, C, R, SL, SR, LFE L, C, R, SL, SR, LFE L, R L, R, SC L, R L, R L, C, R, SL, SR, LFE L, C, R, SL, SR, LFE L, R L, R, SC L, R L, C, R, SL, SR, LFE L, R L, R, SC L, R L, C, R, SL, SR, LFE L, R L, R, SC L, R L, C, R, SL, SR, LFE L, C, R, SL, SR, LFE L, C, R, SL, SR, LFE L, R L, C, R, SL, SR, LFE L, R L, R, SC L, R L, R L, C, R, SL, SR, LFE L, R L, R, SC L, R L, C, R, SL, SR, LFE Note: • • • Dolby Digital (2 ch: Lt/Rt): signal with Dolby Surround flag Speakers are full set. When DOLBY DIGITAL, DTS, PCM or ANALOG is blinking, the selected surround mode is unavailable for input signal. No sound outputs from the surround speaker, center speaker and subwoofer if the DVD disc has no surround data. Are you operating the unit properly following user’s guide ? [. . . ]