User manual MARANTZ SR6001

[. . . ] Model SR6001 User Guide AV Surround Receiver CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. IMPORTANT SAFETY INSTRUCTIONS READ BEFORE OPERATING EQUIPMENT This product was designed and manufactured to meet strict quality and safety standards. There are, however, some installation and operation precautions which you should be particularly aware of. Read Instr uctions ­ All the safety and operating instructions should be read before the product is operated. [. . . ] · The setting for surr. back L and surr. back R appears if it is set, two surround back speakers in the SPEAKER SIZE menu. BACK appears if it is set for one surround back speaker in the SPEAKER SIZE menu. TEST MODE: Select "MANUAL" or "AUTO" generation of the test tone with the 1 or 2 cursor buttons. If you select "AUTO", the test tone will be cycled through in a circular pattern beginning at Left Center Right Surround Right Surround Back Right Surround Back Left Surround Left Subwoofer Left, in 2 seconds increments for each channel. Using the 1 or 2 cursor buttons, adjust the volume level of the noise from the speaker so that it is the same level for all the speakers. If you select "MANUAL", adjust the output level of each speaker as listed below. ENGLISH 12. Move the cursor to FRONT L by pressing the Remember the level of this noise and then press the 4 cursor button. 4 cursor button. The SR6001 will emit a pink noise from the front left speaker. (Note that this can be adjusted to any level between -12 and +12 dB in 0. 5 dB increments. ) The SR6001 will now emit the pink noise from the center speaker. 11. After you complete this portion of the setup, move the cursor to "NEXT" with the 3, 4, 1 and 2 cursor buttons and press the ENTER button to go to the next page. 13. Using the 1 and 2 cursor buttons, adjust the volume level of the noise from the center speaker so that it is the same level as the front left speaker. <SPEAKER LEVEL> SPEAKER LEVEL TEST MODE : MANUAL FRONT L : 0. 0dB CENTER : 0. 0dB FRONT R : 0. 0dB SURR. R : 0. 0dB SURR. B R : 0. 0dB SURR. B L : 0. 0dB SURR. L : 0. 0dB SUB W : 0. 0dB RETURN BACK EXIT 14. The SR6001 will now emit the pink noise from the front right speaker. 15. Repeat steps 13 and 14 for the front right and other speakers until all speakers are adjusted to the same volume level. After you complete this portion of the setup, press the ENTER button to move the cursor to "RETURN". Notes: · Speakers for which you selected "NONE" in the SPEAKER SIZE menu will not appear. Back R appear if it is set for two surround back speakers in the SPEAKER SIZE menu. Back appears if it is set for one surround back speaker in the SPEAKER SIZE menu. · To adjust the speaker levels for 7. 1 channel input sources, you will need to use the 7. 1 Ch Input sub menu. (See page 37) · SUB W can be set from ­18dB to +12dB. Here you can set the volume for each speaker so that they are all heard by the listener at the same level. We recommend holding a dB SPL (Sound Pressure Level) meter at the listening position, at arms length, and pointing straight up at the ceiling, adjust the level of each speaker in turn unit it reads 75dB SPL when the meter is set to "C" weighting and Slow responce. Note: · The speaker level settings are not available in 7. 1 Channel Input mode, Pure Direct mode and Source Direct mode. 36 This menu is for setting surround effect parameters for the various surround input signals so as to bring out the live audio effect of your speaker system. · CHANNEL LEVEL: "3-1 CHANNEL LEVEL" (see page 37) · PLIIx MUSIC PARAMETER: "3-2 PLIIx MUSIC PARAMETER" (see page 38) · CSII PARAMETER: "3-3 CSII PARAMETER" (see page 38) · NEO:6 PARAMETER: "3-4 NEO:6 PARAMETER" (see page 38) CHANNEL LEVEL PL x MUSIC PARAMETER CS PARAMETER NEO:6 PARAMETER HT-EQ LFE LEVEL : : OFF 1. Select "3. SURR SETUP" from MAIN MENU with 3 or 4 cursor buttons and press the ENTER button. Select "CHANNEL LEVEL" with the 3 or 4 cursor buttons and press the ENTER button. [. . . ] 3012, 3034, 3040, 3083 Victor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3040, 3083 Video Concepts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3012, 3034 3040, 3073, 3083 Videosonic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3021 Wards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3005, 3009, 3012 3021, 3026, 3027 3032, 3035, 3045 3052, 3060, 3061, 3067 White Westinghouse . . . . . . . . . . . . . . . . . . . . . . 3035, 3056 XR-1000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3009, 3035, 3067 Yamaha . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3029, 3034, 3040 3072, 3083, 3084 Zenith . . . . . . . . . . . . . . 3030, 3052, 3053, 3059, 3071 DVD Aiwa. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2036, 2037 Apex . . . . . . 2012, 2017, 2018, 2019, 2021, 2034 BOSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2038, 2039 Denon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2047, 2048 Funai . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]