User manual MARANTZ ZC4001

[. . . ] Model ZC4001 User Guide Audio Client ENGLISH WARRANTY For warranty information, contact your local Marantz distributor. RETAIN YOUR PURCHASE RECEIPT Your purchase receipt is your permanent record of a valuable purchase. It should be kept in a safe place to be referred to as necessary for insurance purposes or when corresponding with Marantz. IMPORTANT When seeking warranty service, it is the responsibility of the consumer to establish proof and date of purchase. [. . . ] - L'apparecchio va installato in prossimità della fonte di alimentazione, in modo che quest'ultima sia facilmente accessibile. INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 This section must be read before any connection is made to the mains supply. EQUIPMENT MAINS WORKING SETTING Your Marantz product has been prepared to comply with the household power and safety requirements that exist in your area. ZC4001 can be powered by 230V AC only. TOP PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 PLC SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 SLEEP TIMER SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 BASS BOOST SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The ZC4001 demodulates the sent signals and converts them back to analog signals. * If the condition of the power line degenerates because of the effects of noise from other devices or for other reasons, the ZR6001 uses an audio format of different sampling rate and data bit length. ROOM A ZR6001 POWER ON/STANDBY PHONES SURROUND MODE OPEN/CLOSE PLAY STOP DVD VIDEO BS DIGITAL TV FM/AM MEMORY MODE F/P TUNING PAUSE PREV. NEXT 1 RC2020MD Home power line ROOM B ROOM C ZC4001 ZC4001 2 q STANDBY 1 . POWER ON/STANDBY w q SPEAKERS w INFRARED receiver window z This window receives infrared signals for the remote control unit. z x c v v CONTROL buttons b n POWER button and STANDBY indicator When this button pressed once, the unit turns ON and the display illuminates. When pressed again, the unit turns OFF and the STANDBY indicator will be illuminated. These buttons are used when operating the PLAY, STOP, PAUSE, and other commands of a source. b x FL DISPLAY AND INDICATOR SOURCE buttons These buttons are used to switch the source of ZR6001. INPUT jack on the rear panel. MUTE button Press this button to mute the output to the speakers. Press it again to return the previous volume level. a s n VOLUME UP( )/DOWN( ) buttons This button is volume control of the ZC4001. c Cursor ( , , , )/ENTER buttons These buttons are used to operate the menu system and source units. d a s Function display area d f This area displays the input source. f Volume/ Text display area This area displays the volume and other text. PLC Status display area Clock display area This area displays the PLC reception strength. This area displays the time. 3 ENGLISH FRONT PANEL TOP PANEL REAR PANEL REMOTE CONTROL OPERATION The ZC4001 does not come with a remote controller. However, it does have an infrared sensor that functions as a remote control signal receptor, and therefore it can be operated with the system remote controller (RC5500SR, etc. ) of other Marantz products. Remote-controllable range ENGLISH SERVICE ONLY A o ppr x. 5 m 60° q q w e AC Power cable e Connect the power outlet on the wall. EXT INPUT This is the analog audio input. The audio inputs require RCA-type connectors. w SERVICE ONLY This is a servicing port. Do not connect anything to it. 4 CONNECTING AUDIO COMPONENTS There is one Audio EXT INPUT jack on the rear panel. You can use this jack to input analog audio signal from CD, TAPE DECK, or other analog source component. CONNECTING AC POWER CABLE Connect the AC power cable of the ZC4001 to a wall electrical outlet. Also connect the AC power cable of the ZR6001 to a wall electrical outlet. ROOM A When a ZC4001 and ZR6001 are connected over PLC, another ZR6001 cannot be added to the same power line and connected over PLC. In this case, PLC signals are not sent. ZC4001 ZR6001 ZC4001 POWER ON/STANDBY PHONES SURROUND MODE OPEN/CLOSE PLAY STOP DVD VIDEO BS DIGITAL TV FM/AM MEMORY MODE F/P TUNING PAUSE PREV. NEXT 1 ZR6001 ZR6001 Home power line ROOM B ROOM C If a ZR6001 and ZC4001 are connected over PLC in a nearby apartment unit for example, and there is only a short distance between your apartment and your neighbor's, the PLC signals from your neighbor's apartment can travel over power lines to your place, mix with your system, and prevent audio output. ZC4001 ZC4001 ZC4001 ZC4001 Up to four ZC4001 units may be connected to the same system at one time. ZR6001 ZR6001 5 ENGLISH CONNECTIONS Notes: · The ZC4001 and ZR6001 send audio data over power lines. Therefore, if the condition of the power line degenerates seriously because of the effects of noise from other devices or for other reasons, audio data may not be received or may skip. [. . . ] SYMPTOM CAUSE REMEDY Connect the power plug to the outlet. HOW TO RESET THE UNIT Should the operation or display seem to be abnormal, reset the unit with the following procedure. The ZC4001 is turned on, press and hold the MUTE and STOP buttons simultaneously for 3 seconds or more. STANDBY 1 . Another device is generating a high Turn OFF the device that is causing the noise or level of noise on the power line. Two ZR6001 units are connected to the Using the OSD menu system, set "MULTI PLC same system. Replace all the batteries with new ones. POWER ON/STANDBY 362 mm 120 mm 128 mm Control with the remote control unit fails. [. . . ]