User manual MCINTOSH MCC406M
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual MCINTOSH MCC406M. We hope that this MCINTOSH MCC406M user guide will be useful to you.
You may also download the following manuals related to this product:
MCINTOSH MCC406M DATASHEET (164 ko)
Manual abstract: user guide MCINTOSH MCC406M
Detailed instructions for use are in the User's Guide.
[. . . ] Power Amplifier
MCC406M Owner's Manual
McIntosh Laboratory, Inc.
2 Chambers Street
Binghamton, New York 13903-2699
Phone: 607-723-3512
FAX: 607-724-0549
The lightning flash with arrowhead, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING - TO REDUCE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.
To prevent the risk of electric shock, do not remove cover or back. No user serviceable parts inside.
IMPORTANT SAFETY INSTRUCTIONS!
PLEASE READ THEM BEFORE OPERATING THIS EQUIPMENT.
1. Do not install near any heat sources such as radiators, heat ducts, or other apparatus (including amplifiers) that produce heat. [. . . ] Connect cables (up to 12 AWG) from the Subwoofer Loudspeaker Drivers to the MCC406M Power Ampli-
fier Channels 5 and 6 BRIDGED connection being careful to observe the correct polarities. Connect audio cables from the McIntosh Control Center Front and Rear Outputs to the MCC406M Power Amplifier Inputs 1, 2, 3, and 4. Connect the optional McIntosh external Subwoofer Remote Volume Control to the SUB REMOTE CONTROL Jack on the right side of the MCC406M Power Amplifier. Connect the MCC406M to the vehicle battery terminals using size 4 AWG (Maximum) cables.
Note: It is advisable to place an in-line fuse of a suitable size as close as possible to the battery.
Left Rear Output Right Rear Output
Power Guard Amp ON
Left Front Output Right Front Output
Left Front Loudspeaker System
McIntosh External Subwoofer Rotary Control
Right Front Loudspeaker System
Left Rear Loudspeaker System (+)
Right Rear Loudspeaker System
- Vehicle + Battery
Fuse (-) Subwoofer
10
How to Connect for Four Channels How to Connect for Four Channels
1. Connect a cable from the Control Center Amp On to the MCC406M ON Connector on the right side of the amplifier.
Note: All cables should be connected to the amplifier before connecting the DC power cables to the battery.
fier Channels 5 and 6 Outputs being careful to observe the correct polarities. Connect audio cables from the McIntosh Control Center Front and Rear Outputs to the MCC406M Power Amplifier Inputs 1, 2, 3 and 4.
Note: The Subwoofer Output Level can be remotely controlled by the optional McIntosh External Subwoofer Rotary Control connected to the SUB REMOTE CONTROL jack on the MCC406M.
2. Connect a cable from a McIntosh Control Center with Power Guard to the MCC406M PG Connector on the right side of the amplifier. Connect cables (up to 12 AWG) from two separate Loudspeaker Systems to the MCC406M Power Amplifier Channels 1 and 2 BRIDGED; 3, and 4 BRIDGED connections being careful to observe the correct polarities. Connect cables (up to 12 AWG) from the Subwoofer Loudspeaker Drivers to the MCC406M Power Ampli-
6. Connect the MCC406M to the vehicle battery terminals using size 4 AWG (Maximum) cables.
Note: It is advisable to place an in-line fuse of a suitable size as close as possible to the battery.
Left Rear Output (Subwoofer Level) Right Rear Output
Optional connections for controlling the Subwoofer Level by using the Front to Rear Fader Control on the Control Center
Subwoofer (+)
Power Guard Amp ON
Left Front Output Optional McIntosh External Subwoofer Rotary Control
Right Loudspeaker System
Right Front Output
(-)
Left Loudspeaker System
(+)
- Vehicle + Battery
Fuse (-)
Subwoofer
11
How to Connect for Three Channels
1. Connect a cable from the Control Center Amp On to the MCC406M ON Connector on the right side of the amplifier.
Note: All cables should be connected to the amplifier before connecting the DC power cables to the battery.
2. Connect a cable from a McIntosh Control Center with Power Guard to the MCC406M PG Connector on the right side of the amplifier. Connect cables (up to 12 AWG) from a Loudspeaker System to the MCC406M Power Amplifier Channels 1 and 2 BRIDGED connections. In a similar manner connect another Loudspeaker system to the 3 and 4 BRIDGED connections, being careful to observe the correct polarities for all connections.
4. Connect cables (up to 12 AWG) from the Subwoofer Loudspeaker Drivers to the MCC406M Power Amplifier Channels 5 and 6 BRIDGED connection being careful to observe the correct polarities. Connect audio cables from the McIntosh Control Center Front Outputs to the McIntosh Custom Environmental Equalizer Inputs 1 and 2. Connect audio cables from the McIntosh Custom Environmental Equalizer Outputs 1 and 2 to the MCC406M Power Amplifier Inputs 1 and 3. Connect the optional McIntosh external Subwoofer Remote Volume Control to the SUB REMOTE CONTROL Jack on the MCC406M Power Amplifier. Connect the MCC406M to the vehicle battery terminals using size 4 AWG (Maximum) cables.
Note: It is advisable to place an in-line fuse of a suitable size as close as possible to the battery.
(+)
Power Guard Amp ON
McIntosh External Subwoofer Rotary Control
Right Front Output Left Front Output
McIntosh Custom Environmental Equalizer
- Vehicle + Battery
Fuse (-)
12
How to Connect for Three Channels
Left Loudspeaker System
Right Loudspeaker System
Subwoofer
13
Top Panel Controls, Display and Switches
CH 5-6 LOW PASS Filter Switch and Control select the high frequency roll-off or flat frequency response
CH 5-6 SENSITIVITY Individual Input Sensitivity Controls for Channels 5 and 6
CH 5-6 MODE Switch selects STEREO or BRIDGED mode of operation
CH 5-6 HIGH PASS Filter Switch and Control select the low frequency roll-off or flat frequency response
POWER GUARD LED lights when the Power Guard Circuit activates for Amplifier Channels 5 or 6
POWER GUARD LED lights when the Power Guard Circuit activates for Amplifier Channels 1 thru 4
INPUT SOURCE Switch for Channels 5-6 selects either CHs 5 and 6, 1 and 2 or Subwoofer (Sum of CHs 1, 2, 3, and 4)
METER indicates Channels 1 thru 4 Power Output
METER indicates Channels 5 and 6 Power Output
CH 1-2 MODE Switch selects STEREO or BRIDGED mode of operation
CH 3-4 MODE Switch selects STEREO or BRIDGED mode of operation
CH 3-4 HIGH PASS Filter Switch and Control select the low frequency roll-off or flat frequency response
INPUT SOURCE Switch for Channels 3-4 selects either CHs 3 and 4 or 1 and 2
CH 1-2 HIGH PASS Filter Switch and Control select the low frequency roll-off or flat frequency response
CH 3-4 LOW PASS Filter Switch and Control select the high frequency roll-off or flat frequency response
CH 1-4 SENSITIVITY Individual Input Sensitivity Controls for Channels 1, 2, 3 and 4
14
How to Operate the MCC406M Introduction
The McIntosh MCC406M is a highly versatile amplifier that can be configured in many ways. The best way to set the filter controls is through the use of a real-time spectrum analyzer and the expertise of a professional installer. This manual will guide you through the basic operation, however we suggest you refer to your Dealer for further information on the use of this unit. To access the Amplifier Controls and Switches refer to "Removing the Glass Panel" located on page 6 of this Owner's Manual. [. . . ] Replacing the fuse, if there is problem in the amplifier, may incur a risk of further damage. Refer to figures 10, 11 and 12.
Caution: Disconnect the Amplifier from the Vehicle Battery ( or DC Power Supply) as Potentially Dangerous Currents exist inside the amplifier.
Remove Top Cover Screws
Figure 10
1. Before accessing fuses, disconnect both the positive and negative power cables from the DC input terminals on the left side of the amplifier using a 5/32" hex key. Remove the Top Glass Panel by first removing the four hex bolts with the supplied 3/32" hex key. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE MCINTOSH MCC406M
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual MCINTOSH MCC406M will begin.