User manual MCINTOSH MHT100

[. . . ] Owner's Manual MHT100 A/V System Controller Manufactured under license from Dolby Laboratories, "Dolby", "Pro Logic" and the double-D symbol are registered trademark of Dolby Laboratories, Inc. "DTS", "Digital Surround", and "Coherent Acoustics" are registered trademark of DTS Technology, LLC. and manufactured under license from DTS Technology LLC. MHT100 McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 FAX: 607-724-0549 The lightning flash with arrowhead, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING - TO REDUCE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL. To prevent the risk of electric shock, do not remove cover or back. [. . . ] Using the Up or Down directional push-buttons select number 1 (NOISE) from the Speaker Level OnScreen Menu, followed by pressing the Left or Right directional push-buttons to active the Automatic Loudspeaker Switching Mode. Refer to figure 18. Note: The word OFF, located to the far right of the word NOISE, will change to show which channel is active for making a level change. A G Clef Symbol ( ) will also appear to the right of the numerical value instead of dB. The test signal will start cycling continuously through all Loudspeakers in 3-second intervals. 6. As the test signal stops at each Loudspeaker, adjust the volume of the test signal by pressing the LEVEL Up or Down Push-button on the Remote Control. If an adjustment is made on a Loudspeaker, there is an additional 3-second time interval before the system switches to the next Loudspeaker. As a level is changed, the on-screen display instantly indicates the level change. Note: If the level is increased or decreased, the display will indicate numbers or minus numbers. 7. As the test signal switches to succeeding Loudspeakers, repeat the level adjustment process until the test signal volume levels of all the Loudspeakers are the same, then select EXIT on the menu. The MAIN SYSTEM SETUP Menu will reappear on the Monitor/TV screen. Note: The Loudspeaker level cycling mode can be repeated as often as necessary. 8. If you do not wish to perform SUBWOOFER SETTINGS Adjustments at this time, then proceed to the next step. 29 How to Adjust Speaker Levels, con't 9. If you are satisfied with the changes that you may have made, select YES to save those changes or NO not to save them. Manual Speaker Level Switching The Manual Speaker Level Switching Mode allows for using either the built-in Noise Source or using an external Audio Test Source for setting the Loudspeaker Levels. If you choose to use the built-in Noise Source proceed to step 10; go to step 18 for using an external Audio Test Source. Using the Up or Down directional push-buttons select number 1 (NOISE) from the Speaker Level On-Screen Menu, followed by pressing the Left or Right directional push-buttons to active the Automatic Loudspeaker Switching Mode. Refer to figure 18. Note: The word OFF, located to the far right of the word NOISE, will switch to show which channel is active for making a level change. A G Clef Symbol ( ) will also appear to the right of the numerical value instead of dB. The test signal will start cycling continuously through all Loudspeakers in 2-second intervals. MENU: SPEAKER LEVEL 1. SUBWOOFER EXIT LEFT 0. 0 0. 0dB 0. 0dB 0. 0dB 0. 0dB 0. 0dB 0. 0dB Figure 18 MENU: SPEAKER LEVEL 1. Using the Up or Down directional push-buttons select number 2 (LEFT FRONT) from the Speaker Level On-Screen Menu. Adjust the volume of the test signal by pressing the LEVEL Up or Down Push-button on the Remote Control. Note: The Left Front Loudspeaker volume level can serve as a reference. If the level is increased or decreased, the display will indicate numbers or minus numbers. 0. 0 0. 0dB 0. 0dB 0. 0dB 0. 0dB 0. 0dB 0. 0dB 13. Using the Up or Down directional push-buttons select number 3 (CENTER) from the Speaker Level On-Screen Menu. [. . . ] If you are satisfied with the changes that you may have made, select YES to save those changes or NO not to save them. PRESET ASSIGNED FM1 Auto 91. 50 MHz Jazz-BA Yes EXIT Figure 67 54 How to Operate the Tuner How to Operate the Tuner The McIntosh MHT100 TM1 AM/FM Tuner Module incorporates an advanced design AM/FM Tuner with many desirable performance features to enhance your enjoyment of radio broadcasts. There are several methods of tuning to an AM/FM Broadcast Station by using the Front Panel Trim/Tune Function and the Remote Control. When a station is selected, the Front Panel Alphanumeric Display will indicate (from left to right) Station Signal Strength from 1 to 9, a dot if the Broadcast is Stereo, the AM/FM Station Frequency, AM or FM Broadcast Band and a Preset Number (if that station has been assigned a Preset). [. . . ]