User manual MCINTOSH MX136 AUDIO AND VIDEO PREAMPLIFIER/PROCESSOR

[. . . ] A/V Control Center MX136 Owner's Manual Manufactured under license from Dolby Laboratories. "Dolby", "Pro Logic" and the double-D symbol are trademarks of Dolby Laboratories. Patent No's: 5, 451, 942; 5, 956, 674; 5, 974, 380; 5, 978, 762; 6, 226, 616; 6, 487, 535 & other U. S. DTS, DTS Digital Surround and Neo:6 are registered trademarks and the DTS logos and Symbol, and DTS 96/24 are trademarks of DTS, Inc. [. . . ] Press the SELECT/OK Push-button to switch Off the Manual Loudspeaker Level Switching Mode. If you do not wish to perform INPUT SETUP Adjustments at this time, select MAIN MENU from the menu. The MAIN SYSTEM SETUP Menu will reappear on the Monitor/TV screen and proceed to the next step. If you are satisfied with the changes that you may have made, select YES to save those changes or NO not to save them. Refer to figure 7 on page 27. Loudspeaker Levels Location Default Setting New Setting Left Front Center Right Front Right Surround Right Back Sur Left Back Sur Left Surround Subwoofer 0dB 0dB 0dB 0dB 0dB 0dB 0dB 0dB SETUP, con't How to Change the Input Setup The MX136 has twelve Analog Audio Inputs numbered 0 through 11, six Digital Audio Inputs lettered A through F and five Component Video Inputs numbered 1 through 5. These inputs already have assigned titles and associations that will allow for immediate hookup, operation and enjoyment. If these starting assignments and associations do not match up with components in your system, they may be reassigned from the default settings. The following example will illustrate how to rename the TAPE2 Input to DVD2 and assign it the LV Digital Input. When the Zone A or B Input Selector is rotated to select what was originally the TAPE2 Input, DVD2 will now appear on the Front Panel Alphanumeric Display. The Surround Mode, Video Power Control, HDMI Video and Component Video can also be set for each Input. Notes: 1. The very first time the INPUT SETUP is accessed, the default settings will be indicated. Unused Inputs may be switched Off so that they will not appear when rotating through the input source choices using the Zone A or Zone B Input Selector and also will not be available when using the Remote Control or Keypad. MENU: INPUT SETUP SOURCE INPUT 5 IR-TP2 TITLE TAPE2 DIGITAL INPUT NONE ZONE A ANALOG INPUT RCA SURR MODE LAST VIDEO POWER ON HDMI VIDEO NONE COMPONENT VIDEO NONE MAIN MENU Figure 15 1. Press and hold the Front Panel SETUP Push-button approximately three seconds to enter the Setup Mode. The word SETUP will appear on the MX136 Front Panel Display and the MAIN SYSTEM SETUP Menu will appear on the Monitor/TV screen. Using the Up or Down directional push-buttons on the Remote Control, select INPUT SETUP on the OnScreen Menu, followed by the SELECT/OK Push-button. Using the Up or Down directional push-buttons, select SOURCE INPUT from the On-Screen Menu, followed by pressing the Left or Right directional push-buttons to select Input Number 5 - IR-TP2. Refer to figure 15. Note: The information displayed after the Source Input Number indicates which IR Remote Control Command selects the input. 6. Press the Right directional push-button to select the second character position of the title. Using the Up or Down directional push-buttons to select "V" the second character of the title. Select the two remaining characters "D" and "2" of the title by using the directional push-buttons. Press the SELECT/OK Push-button once and then press the Down directional push-button. If you do not wish to perform Digital Input Setting at this time, proceed to the ZONE A Analog Input Setting. MENU: INPUT SETUP SOURCE INPUT 5 - IR-TP2 TITLE A DIGITAL INPUT NONE ZONE A ANALOG INPUT RCA SURR MODE LAST VIDEO POWER ON HDMI VIDEO NONE COMPONENT VIDEO NONE MAIN MENU Analog Audio/Video Input Title 4. [. . . ] Press and Hold the ENTER Push-button for approximately 3 seconds until the Front Panel Alphanumeric Display indicates the word CLEARED. Refer to figure 68. Note: If you wish to replace an already assigned Station Preset with another radio station, it is not necessary to clear the Preset first, just enter in the new station for that Preset. The new station will automatically replace the previously assigned station. Figure 65 1. Press the Front Panel TUNING Up or Down Pushbutton to select a station. [. . . ]