User manual MERCURY MARINE SMARTCRAFT

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual MERCURY MARINE SMARTCRAFT. We hope that this MERCURY MARINE SMARTCRAFT user guide will be useful to you.


MERCURY MARINE SMARTCRAFT : Download the complete user guide (1007 Ko)

You may also download the following manuals related to this product:

   MERCURY MARINE SMARTCRAFT ANNEXE 227 (265 ko)

Manual abstract: user guide MERCURY MARINE SMARTCRAFT

Detailed instructions for use are in the User's Guide.

[. . . ] The engines must be programmed for proper engine location using a DDT or Quicksilver Diagnostic Tool. Flashing "nonE" ­ The gauge does not see any engine computers (ECMs). Please check wiring for bad connections and for proper amount of terminator resistors. Flashing "noSt" ­ None of the engine computers (ECMs) are configured as a starboard engine. [. . . ] (continued on next pge) 12 WARNING SYSTEM Warning Display Screens IMPORTANT: Refer to the Engine Operation, Maintenance and Warranty Manual for further explanation of the problem and the correct action to take. Water in the water-separating fuel filter reached the full level. Water in Fuel Engine Overspeed The Bell icon is displayed. The engine speed exceeded the maximum allowable RPM. Engine Malfunction The Bell and Engine Icon will appear to inform the driver that an engine problem occurred. Oil Pump Fault / Low Oil Pressure The Bell, Engine and oil icons are displayed. No lubricating oil is being supplied to the engine. 13 CAL 1 CALIBRATION Cal1 Display Calibrations: ·(On or Off) Trim Pop up Screen ·Trim Calibration ·English or Metric Units Selection ·Range/Distance Units Selection ·(On or Off) Depth, Trim, Engine Temperature, Oil Pressure, Oil Temperature, Water Pressure, Volts, Engine Hours, Speed, Seawater Temperature and Data Simulator pages. 1. for 3 seconds to bring up the and when depth screen is disNOTE:Press and hold played will open the depth calibration menu. for 3 seconds to get out of Cal 1 Start Screen Press the button to move to the next calibration screen. Tri m Trim Pop-up Screen (Turn on or off) Select whether you want the power trim display screen to pop up whenever the trim switch is activated. 1. Press the button to select. button to move to the next function. 14 CAL 1 CALIBRATION Trim Trim Sensor 0. 0 Setting (Full Trim in Position) 1. button to advance to 10. 0 setting. Trim Sensor 10. 0 Setting (Full Trim Out Position) 5. button to advance to 25. 0 setting. Trim Sensor 25. 0 Setting (Full Trailer Out Position) 9. Use the trim switch and trim unit out to the maximum trailer position. button to move to the next function. 15 CAL 1 CALIBRATION SAE English System F Psi Ft Metric System C Bar Ltr M English or Metric Gal Select whether you want the readings in the SAE English system or the Metric system. 1. button to move to the next function. Range Readings Miles NMiles Km Miles Select whether you want the readings in Miles, Nautical Miles or Kilometers. 1. button to move to the next function. Depth Display (on or off) Select whether you want the depth screen to be displayed. Trim Trim Display (on or off) Select whether you want the trim screen to be displayed. 1. button to move to the next function. 16 CAL 1 CALIBRATION Coolant Temperature Display (on or off) Select whether you want the coolant temperature screen to be displayed. button to move to the next function. Oil Pressure Display (on or off) Select whether you want the oil pressure screen to be displayed. for 3 seconds to get out of Cal 2 Start Screen Press the button to move to the next calibration screen. Pitot Water Pressure Sensor Input Select the pressure input of the Pitot water pressure sensor on the engine. NOTE:The standard speed input on production Mercury Outboards is 100 PSI. Press the button to move to the next function. 20 CAL 2 CALIBRATION Paddle Wheel Speed Sensor Frequency Miles Frequency can be changed to match requirements of different sensors. 4. 9 is the frequency of the paddle wheel speed sensor provided by Mercury Marine. Press the button to save and move to the next function. Seawater Temperature Display (on or off) Indicates if a seawater temperature sensor is installed. NOTE: You must have a Mercury paddlewheel or depth/temp transducer (purchased separately) connected to the system in order for this screen to operate . Press the button to save and move to the next function. Pitot Multiplier Screen Allows you to adjust the speedometer value to match another speedometer, such as a GPS. [. . . ] NOTE:If you choose oil or water/waste icon, no further tank 2 calibration will be needed. Press the button to continue. Tank 2 Calibration 0% Setting Gal Have the fuel tank level at empty. Press the vance to 25% setting. 26 CAL 2 CALIBRATION Tank 2 Calibration 25% Setting Gal 25 Percent Fuel to Add Adding the amount of fuel shown will raise fuel tank level to 25 percent. NOTE :The quantity of fuel to add is determined by the fuel tank capacity number entered. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MERCURY MARINE SMARTCRAFT




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual MERCURY MARINE SMARTCRAFT will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.