User manual NAPCO MAGNUM ALERT RP1016 LCD KEYPAD

[. . . ] These detection devices are divided among separate areas known as "zones", set up throughout your premises. Each zone number corresponds to a Zone light on your Keypad's gray display area. When a zone's red light is ON (or lit), it indicates that one or more detection device(s) assigned to that area are active o r open. For example, if Zone 1 is the front door, and it is open, the Zone 1 light will be on. If zone 2 is a motion detector, and the re is movement in that area, Zone light 2 will turn ON. [. . . ] If your system has the Ambush feature enabled, the code assigned as the User 6 code will function as your Ambush Code. 7 Oi218a page 7 Tuesday, September 16, 1997 08:28 Disarming Your System / Silencing an Alarm Disarming Your System when Returning 1 2 ARMED READY SYSTEM FIRE AC Enter your premises through the Entry/Exit door. The keypad will sound a steady tone to remind you to disarm the system before your Entry Delay time expires. The Red Armed light will go out, indicating that the system has been disarmed. Note: If you make a mistake entering your code, press the Alarm Indication If the Red Armed light is flashing rapidly, an alarm occurred while you were away. For your own protection, leave immediately and call authorities from a neighbor's phone . Silencing an Alarm In the event that the system goes into alarm due to a violated burglary zone, the bell or siren will sound and the keypad sounder will also activate. zone which went into alarm will continue to flash until ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 Silencing a Fire Alarm In the event that the Fire alarm activates due to an violated smoke or fire detector, the bell or siren will sound a distinct pulsating tone. The Red FIRE light on the keypad will be flashing, and the keypad sounder will emit a pulsing tone. If a Fire Alarm does occur: 1 2 3 4 If a fire is in progress, evacuate the premises immediately!Call the Fire Department from an outside phone. The bell or siren will silence, and the FIRE light on the keypad will stop flashing but will still be lit. If you are protected by smoke detectors, the light on the active to reset the fire zone. Call installing company for service. ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 1 Beep 2 Low Battery 1 Beep 3 Communication Failure 1 Beep 4 Telephone Line Cut . 2 Beeps 1 Bell/Siren Trouble 12 Oi218a page 12 Tuesday, September 16, 1997 08:28 9System Troubles 'SYSTEM Keypad Beeps or Flashes 2 Beeps 2 Beeps 2 Beeps ARMED READY SYSTEM FIRE AC Zone light System Trouble ON Condition 2 Fire Trouble 3 4 1-6 Action 3 Beeps ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 4 Beeps 1-6 5 Beeps 1-4 6 Beeps 1-4 7 Beeps 1-6 A problem has been detected in the Fire Circuit. Wireless Receiver A problem has been detected with the wireless receiver. Wireless Receiver A problem has been detected with a wireless receiver. The battery in a wireless transmitter is low and should be reWireless placed. This transmitter is on the zone corresponding to the numTransmitter Low ber of the lit zone light. The replacement battery for the GEMBattery Trans2 door/window transmitter, GEM-PIR motion detector and GEM-GB glass break detector is the Duracell DL123A. (2 required for the GEM-PIR and GEM-GB. ) The GEM-DT Dual Technology Sensor requires C-Cell Duracell MN1400 batteries(4). Warning: Replace batteries only with the same type as specified above. Wireless Call installing company for service Transmitter Supervisory Failure The battery in a wireless smoke detector is low and should be Wireless Smoke Detector Low Bat- replaced. This wireless smoke detector should be marked with a number corresponding to the number of the lit zone light. The tery replacement batteries required are Duracell 9 Volt Alkaline (2). [. . . ] THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. THERE IS NO EXPRESS OR IMPLIED WARRANTY OF MERCHANTABILITY OR A WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. ADDITIONALLY, THIS WARRANTY IS IN LIEU OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE PART OF NAPCO. Any action for breach of warranty, including but not limited to any implied warranty of merchantab ility, must be brought within the six months following the end of the warranty period. [. . . ]