User manual NAPCO RP-1016
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual NAPCO RP-1016. We hope that this NAPCO RP-1016 user guide will be useful to you.
Manual abstract: user guide NAPCO RP-1016
Detailed instructions for use are in the User's Guide.
[. . . ] These detection devices are divided among separate areas known as "zones", set up throughout your premises. Each zone number corresponds to a Zone light on your Keypad's gray display area.
When a zone's red light is ON (or lit), it indicates that one or more detection device(s) assigned to that area are active o r open. For example, if Zone 1 is the front door, and it is open, the Zone 1 light will be on. If zone 2 is a motion detector, and the re is movement in that area, Zone light 2 will turn ON. [. . . ] This is typically followed by done in the evening when all family members are home for the night. Instant Mode can be activated at any time after the system has been armed. The Red Armed light will flash rapidly while in the Instant Mode.
!
Easy Exit (optional)
Your System may have been programmed to allow Easy Exit, which allows a user to exit the premises ollowed by the protection is removed from the Exit/ Entry with the system armed. This will allow, for example, an early morning commuter to exit the house in the morning, without having to disarm and rearm the system, waking the family.
f
,
Arming With a System Trouble Present (the 9 System Light is Lit)
If the XP400 has a system trouble present, the SYSTEM light will be lit and the keypad sounder pulsing. If you cannot immediately clear the system trouble, the system can still be armed. Simply o view the trouble, press again to reset the trouble and then arm the system. 7
t
'
Oi220a page 7
Tuesday, September 16, 1997 08:30
Emergency Conditions
& &
Yes
Emergency Buttons
Auxiliary Emergency Enabled?No
The two sets of emergency buttons, if programmed, are always active whether the system is armed or disarmed. The emergency signal will only be activated when the two respective buttons are pressed at the same time.
to alert the central station of an auxiliary Simultaneously press emergency, if so programmed. (The nature of this emergency alarm is to be determined by the installer)
Yes
to sound a police emergency alarm, and to alert Police Emergency: Simultaneously press the central station of a fire emergency, if so programmed.
&+ +
Ambush Alarm Enabled?Yes No
Ambush Alarm
In the event that you are forced by an intruder to disarm your system, the ambush alarm can be activated. If this is due to a temporary interruption in the telephone service, the trouble can be cleared when the service is restored by pressing . If telephone service has been temporarily interrupted, the trouble will clear it is when restored. Otherwise, call installing company for service.
1 Beep
2
Low Battery
1 Beep
3
Communication Failure
1 Beep
4
Telephone Line Cut
12
Oi220a page 12
Tuesday, September 16, 1997 08:30
9System Troubles
'SYSTEM
ARMED READY SYSTEM
Keypad Beeps or Zone light ON Flashes 2 Beeps 2 Beeps 2 Beeps 3 Beeps 1 3 4 1-4
System Trouble Condition
Action
Bell / Siren Trouble There is a problem with the Bell or Siren. Wireless Receiver Trouble Wireless Receiver Jam Wireless Transmitter Low Battery A problem has been detected with the wireless receiver. This transmitter is on the zone corresponding to the number of the lit zone light. The replacement battery for the GEM-Trans2 door/window transmitter, GEM-PIR motion detector and GEM-GB glass break detector is the Duracell DL123A. (2 required for the GEM-PIR and GEM-GB. ) The GEM-DT Dual Technology Sensor requires 4 C-Cell Duracell MN1400 Alkaline batteries. Warning: Replace batteries only with the same type as specified above. Call installing company for service Call installing company for service.
ZONE 1 ZONE 2 ZONE 3 ZONE 4
4 Beeps
1-4
Wireless Transmitter Supervisory Failure Zone Trouble
7 Beeps
1-4
13
Oi220a page 13
Tuesday, September 16, 1997 08:30
Glossary
Ambush Code - In the event that you are forced by an intruder to disarm your system, this special code can be used to disarm the system, and simultaneously send a silent alarm to Central Station. If your system has the Ambush feature enabled, the code assigned as the User 4 code will function as your Ambush Code Arming / Disarming - Turning the system on or off by entering your user code at the keypad. Auto Interior Bypass - A feature which allows the system to recognize when you have not left the premises and automatically bypass any interior zones, deactivating devices such as motion sensors, allowing free movement throughout the premises. [. . . ] THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. THERE IS NO EXPRESS OR IMPLIED WARRANTY OF MERCHANTABILITY OR A WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. ADDITIONALLY, THIS WARRANTY IS IN LIEU OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE PART OF NAPCO. Any action for breach of warranty, including but not limited to any implied warranty of merchantab ility, must be brought within the six months following the end of the warranty period. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE NAPCO RP-1016
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual NAPCO RP-1016 will begin.