User manual ONE FOR ALL URC 7557

[. . . ] νική Русский Türkçe URC7557_Full-Manual_English:Ofa5_Digital_URC7555_EURO_10_Talen 17-11-10 09:41 Pagina English Table of Contents 2 3 3 PICTURE OF ONE FOR ALL 5 REMOTE INSTALLING THE BATTERIES THE KEYPAD SETTING UP THE ONE FOR ALL 5 (How to set up the ONE FOR ALL 5 to control your devices) SEARCH METHOD 6 7 SET UP CODES TV VCR : Television / LCD / Plasma / Projector / Rear Projector. CODE BLINK OUT (To find out which code is currently programmed) QUICK CODE REFERENCE THE LEARNING FEATURE (How to copy functions from your original working remote onto the ONE FOR ALL 5) OPERATIONAL RESET EXTRA FEATURES • Mode re-assignment (Changing a device mode) • Volume Punch-Through • Macros (Sequence of commands) • Key Magic (How to program missing functions) • Colour and Brightness TROUBLE-SHOOTING 8 8 9 11 12 13 14 16 17 17 WWW. COM URC7557_Full-Manual_English:Ofa5_Digital_URC7555_EURO_10_Talen 17-11-10 09:41 Pagina Installing the Batteries Your ONE FOR ALL 5 requires 4 new “AAA/LR03” alkaline batteries. Match the batteries to the (+) and (–) marks inside the battery case, then insert the batteries. [. . . ] Quick Code Reference Write down the codes for your devices in the boxes below and in the battery compartment for quick and easy reference. COM 8 URC7557_Full-Manual_English:Ofa5_Digital_URC7555_EURO_10_Talen 17-11-10 09:41 Pagina The Learning Feature (How to copy functions from your original working remote onto the ONE FOR ALL5) The ONE FOR ALL 5 comes with a complete library of pre-programmed codes. After you have set up the ONE FOR ALL 5 for your device, you may find that there are one or more keys that you had on your original remote, which do not have a place on the ONE FOR ALL keypad. As a convenience, the ONE FOR ALL 5 offers a special Learning feature that allows you to copy any function from your original remote control onto the keypad of the ONE FOR ALL 5. Before you start: - Make sure your original remote control is working correctly. - If a Shifted Learned function is placed on the Channel and Volume keys then Colour/Brightness will be sacrificed. - You can replace a learned function by placing another learned function on top. - Learning should not be done in direct sunlight or under incandescent lights. - Make sure you are using new batteries before following the instructions above. - Upon changing the batteries, your learned functions will be retained. € Shifted Learning You can also learn a function on a key of the ONE FOR ALL without sacrificing the original ONE FOR ALL function. A Shifted Learning function can also be put on any key EXCEPT for the following: Device keys, MAGIC key, Number keys. To install a Shifted Learning function, simply follow steps 1-8 on the previous page. During step 5, press MAGIC once before you press the key where you are placing the learned function. To access the shifted function, press MAGIC and then the key you have learned on. COM URC7557_Full-Manual_English:Ofa5_Digital_URC7555_EURO_10_Talen 17-11-10 09:41 Pagina The Learning Feature To delete a learned function: 1 Press and hold the MAGIC key until one of the device keys will blink twice. The red LED underneath the corresponding device key (depending on the device mode that was selected) will blink once then twice. Press twice on the learned key which will be deleted (the device key will blink twice). 2 3 4 5 6 * To delete a Shifted Learned feature, press MAGIC before you press the learned key to be deleted (during step 4). To delete all learned functions within a specific mode: 1 Press and hold the MAGIC key until one of the device keys will blink twice. The red LED underneath the corresponding device key (depending on the device mode that was selected) will blink once then twice. 2 3 Operational Reset The Operational Reset will erase all learned functions across all modes and some other programmed functions like Key Magic and Macros. [. . . ] Colour (+) Colour (-) = Press and release MAGIC then hold Volume (+) = Press and release MAGIC then hold Volume (-) Brightness (+) = Press and release MAGIC then hold Channel (+) Brightness (-) = Press and release MAGIC then hold Channel (-) Trouble-Shooting Problem: Your brand is not listed in the code section?Try repeating the Direct Set-Up using another code listed under your brand or start the search method over again to locate the proper code. Enter the channel number exactly as you would on your original remote. As a safety feature on your ONE FOR ALL, you must press the Record key twice. [. . . ]