User manual PANASONIC NE-1027

[. . . ] Operating Instructions NE-1027/NE-1037 1000 Watts Microwave Oven 0 (Min) Min) 12 3 4 30 5 6 7 8 9 25 20 15 10 x2 1 2 3 X2 R Please read these instructions completely before operating this oven. Table of Contents For Your Safety . . 21 -1- For Your Safety This appliance is supplied with a moulded three pin mains plug for your safety and convenience. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of 13 amps and that it is approved by ASTA or BSI to BS1362. If the fuse cover is detachable, never use the plug with the cover omitted. [. . . ] Heating will start. 3. NOTE: · TO STOP THE OVEN, open the door or set the Timer Select Dial back to "0" (zero) position ­­ microwaves will automatically stop. -7- - MEMO - -8- Outline Diagram NE-1037 (1) x2 1 2 3 Digital Display Window (see below) Power Level Pad Program Pad Double Quantity (x2) Pad Start Pad Stop/Reset Pad Memory Pads Control Panel Door Safety Lock System (2) (3) (4) (5) (1) (2) 1 2 (6) (7) (8) (9) (3) 3 4 (10) Oven Window (11) Oven Lamp (7) (11) (4) X2 5 6 7 NE-1037 x2 1 3 (5) 1 2 8 (10) X2 3 4 5 6 7 (8) 9 (6) 8 9 0 0 (9) Digital Display Window Indicator Locations B A x2 C 1 2 3 D E A - Program Change Indicator B - Double Quantity (x2) Heating Indicator C - Memory Pad Number and Heating Time Display (min. sec. ) D - Stage Heating Indicator E - Power Level Indicator 1000 W 500 W 340 W (Defrost) -9- How to Operate Before Operating Make sure the oven is connected to a properly earthed electrical outlet. For the detailed operation, see the page on each feature. This oven is preset at the factory for the following: 1. Memory Pads preset to 1000 W at the indicated heating times for single stage heating. 30 sec. The Double Quantity Pad (x2) preset to automatically double the programmed time of each Memory Pad. (See pages 12, 15) Example: Press X2 5 = 2 min. NE-1037 2. (See page 18) To set the power level: Select power level before programming the cooking time. 1000 W 500 W 340 W (Defrost) To set the cooking time: You can set up to 30 minutes for and 99 minutes 99 seconds for Example 1: To set 15 minutes 45 seconds Press 1 5 4 and . 5 Example 2: To set 85 minutes 30 seconds Press 8 5 3 0 When you press the Start Pad, the display shows 1 hour 25 minutes instead of 85 minutes 30 seconds. When selected cooking time is over an hour, the display shows hours and minutes, but the oven works for your setting time. Display: The display will go blank (when the door is closed): q at more than 1 minute interruption. q at more than 1 minute after completion of heating and removing food. The display will flash "0": q continuously if the door is not opened to remove the food. Oven Light: Oven light will be turned on, when: q the door is opened. Oven light will be turned off, when: q the door is closed (no heating). q heating finishes. - 10 - How to Operate Heating Open the door and place the food in the oven cavity. Manual Single Stage Heating: This feature gives the user maximum flexibility to set the oven to desired heating time and power level. 2 1 0 0 · Press the Memory Pads 2, 0 and 0. 3. · Press the Start Pad. When opening the door, the display will stop blinking. 1 NE-1037 4. Manual 2 or 3 Stages Heating: This feature allows you to set to begin heating at one power level then shift automatically to a different power level after the designated length of heating time. Example: To heat for 2 minutes at 340 W for 2nd stage heating For Stage 1 cooking 1. The stage "2" is blinking. 0 0 1 2 · Follow steps 1 and 2 above table. 2. 2 · Press the Memory Pad 2, 0 and 0. 1 2 3. · Press the Start Pad. · When oven shifts to the next stage, a single beep tone will sound. When opening the door, the display will stop blinking. 1 2 2 4. [. . . ] What to do when a failure code appears: CODE F01 CAUSE * Overcooked food * Temperature of exhausted air is too high WHAT TO DO * Press Stop/Reset Pad to stop beep. * If normal operation does not resume, call the service agent with the information of failure code. F33-34 F44 * Defective sensor circuit * Unplug the oven and wait more than 10 seconds before reconnecting. * When a pad was pressed for more than * If normal operation does not resume, call the service agent with the 2 minutes information of failure code. * Defective pad or control circuit NOTE: Above codes shown in the display do not indicate all the possible failures on the unit. Care of Your Microwave Oven 1. [. . . ]