Detailed instructions for use are in the User's Guide.
[. . . ] IMPORTANT MANUAL
Do Not Throw Away
OWNER'S MANUAL MODEL NUMBER:
PP11530ES
SNOW THROWER
Read the Owner's Manual and follow all Warnings and Safety Instructions. Failure to do so can result in serious injury.
WARNING:
Always Wear Eye Protection During Operation
415153 Rev. 2 09. 20. 07 TH Printed in U. S. A.
Safe Operation Practices for Walk-Behind Snow Throwers
This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury. [. . . ] When the engine starts, release the starter button and slowly move the choke control to the "OFF" position. Disconnect the power cord from the receptacle first, then from the engine. Engine will not develop full power until it has reached normal operating temperature. WARM START - ELECTRIC STARTER Follow the steps above, keeping the choke control in the "OFF" position. Insert safety ignition key (packed separately in parts bag) into ignition slot until it clicks. Push the primer four (4) times if the temperature is below 15°F, or two (2) times if temperature is between 15° and 50°F. NOTE: Over priming may cause flooding, preventing the engine from starting. If you do flood the engine, wait a few minutes before attempting to start and DO NOT push the primer. When the engine starts, release the recoil starter handle and slowly move the choke control to the "OFF" position. Engine will not develop full power until it has reached normal operating temperature. WARM START - RECOIL STARTER Follow the steps above, keeping the choke in the "OFF" position. BEFORE STOPPING Run the engine for a few minutes to help dry off any moisture on the engine. IF RECOIL STARTER HAS FROZEN If the recoil starter has frozen and will not turn the engine, proceed as follows: 1. Grasp the recoil starter handle and slowly pull as much rope out of the starter as possible. Release the recoil starter handle and let it snap back against the starter. If the engine still fails to start, repeat the above steps or use the electric starter.
SNOW THROWING TIPS
· · · · · · · · · · · Always operate the snow thrower with the engine at full throttle. It is easier and more efficient to remove snow immediately after it falls. At this time the snow is usually dry and has not been exposed to the direct sun and warming temperatures. Slightly overlap each successive path to ensure all snow will be removed. For extremely heavy snow, reduce the width of snow removal by overlapping previous path and moving slowly. After snow-throwing is completed, allow engine to run for a few minutes to melt snow and ice off the engine. Clean the entire snow thrower thoroughly after each use and wipe dry so it is ready for next use. [. . . ] 1 inch = 25. 4 mm IMPORTANT: Use only Original Equipment Manufacturer (O. E. M. ) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 29
REPAIR PARTS WHEELS / DECALS
SNOW THROWER - MODEL PP11530ES (96192001901)
10 30 15 32 12 19 11 11 8 28 28 2 18 10 13 14 27
20 17
31 4
22 25 23 33 21 3 4 10 9 24
26 11
29
4
34 29 2 7 18 30 14 15 12 27 28 25
24 21 33 23 26 28 11
4 22 3
1
16 19
34 32 13 20
11
9
8
1
2 4
6
1 3 30 5 10 7
REPAIR PARTS WHEELS / DECALS
SNOW THROWER - MODEL PP11530ES (96192001901)
KEY PART NO. NO.
DESCRIPTION
1 2 3 4 5 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34
196752X421 155443 405161 184471 17060410 17000616 410294X479 410293X479 17600406 17490508 405077 193506X479 182015 194944X008 194939X008 194943X008 181847 85179 179148X479 192126 182466 187622 194941 179139 194940 189282 174697 179830 193885 196753X421 700279 12000045 146315
Wheel Assembly, 16", Power Steering, LH Pin, Klik 1/4 Cover, Power Steering Screw, Hex Head #10-24 x 1/2 Screw Capscrew, Hex Head, Flanged 1/4-20 x 1/16 Bracket, Steering Cable, RH Bracket, Steering Cable, LH Screw, Hex Head 1/4-20 x 1/2 Screw, Hex Head 5/16-18 x 1/2 Link, Steering Lever Yoke, Steering Pin, Steering Lever Bellcrank Bracket, LH Steering Bracket, RH Steering Pin, Steering Bellcrank Retainer, Hairpin Bracket, Steering Driver, Wheel Ring, Wire Retainer Lobe, Wheel Slide, Clutch Spring, Clutch Slide Lobe, Axle Key, Square 1/4 x . 875 Washer, Thrust (1") Bearing, Axle Spring, Return, Steering Latch Wheel Assembly, 16", Power Steering, RH Clip, Retainer Ring, Retaining Screw, Hex Head, Tapping 5/16-18 x 5/8
KEY PART NO. [. . . ]