User manual POULAN PRO PR1742STF

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual POULAN PRO PR1742STF. We hope that this POULAN PRO PR1742STF user guide will be useful to you.


POULAN PRO PR1742STF : Download the complete user guide (949 Ko)

Manual abstract: user guide POULAN PRO PR1742STF

Detailed instructions for use are in the User's Guide.

[. . . ] IMPORTANT MANUAL Do Not Throw Away 02478 OWNER'S MANUAL MODEL: Read this Owner's Manual and follow all Warnings and Safety Instructions. Failure to do so can result in serious injury. WARNING: PR1742STF LAWN TRACTOR Always Wear Eye Protection During Operation 183046 Rev. 2 6. 28. 04 RD/MH Printed in U. S. A. SAFETY RULES Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. I. [. . . ] · Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber. · Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage. NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. · HEX BOLT (GRADE 8)* *A GRADE 8 HEAT TREATED BOLT CAN BE IDENTIFIED BY SIX LINES ON THE BOLT HEAD. FIG. 12) NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced. An unbalanced blade will cause excessive vibration and eventual damage to mower and engine. · The blade can be sharpened with a file or on a grinding wheel. · To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer. ) NOTE: Do not use a nail for balancing blade. · Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced. CENTER HOLE OPERATOR PRESENCE SYSTEM Be sure operator presence and interlock systems are working properly. If your tractor does not function as described, repair the problem immediately. · The engine should not start unless the clutch/brake pedal is fully depressed and attachement clutch control is in the disengaged position. · When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine. · When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine. · The attachment clutch should never operate unless the operator is in the seat. BLADE CARE For best results mower blades must be kept sharp. Replace bent or damaged blades. 5/8" BOLT OR PIN BLADE BLADE REMOVAL (See Fig. 11) · · · Raise mower to highest position to allow access to blades. Install new or resharpened blade with trailing edge up towards deck as shown. FIG. 12 BATTERY Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life. NOTE: The original equipment battery on your tractor is maintenance free. [. . . ] This warranty covers only parts of new Power Train Components which are found upon examination to be defective in material or workmanship as delivered to the original purchaser. This warranty does not cover defects caused by depreciation or damage caused by normal wear, accidents, improper maintenance, improper use or abuse of the product, failure to follow the instructions contained in an Instruction Manual for the operation of the Power Train Component and parts. The cost of normal maintenance and replacement of service items which are not defective shall be paid for by the original purchaser. C. Securing Warranty Service Warranty service can be arranged for by contacting either a Tecumseh Authorized Service Outlet (any Tecumseh Registered Service Dealer, Tecumseh Authorized Service Distributor, or Tecumseh Central Warehouse Distributor) or by contacting Tecumseh, c/o Service Manager, Engine and Transmission Group Service Division, 900 North Street, Grafton, Wisconsin 53024. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE POULAN PRO PR1742STF




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual POULAN PRO PR1742STF will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.