User manual POULAN 961980025

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual POULAN 961980025. We hope that this POULAN 961980025 user guide will be useful to you.


POULAN 961980025 : Download the complete user guide (1312 Ko)

Manual abstract: user guide POULAN 961980025

Detailed instructions for use are in the User's Guide.

[. . . ] IMPORTANT MANUAL Do Not Throw Away OWNER'S MANUAL MODEL NUMBER: 961980025 SNOW THROWER Read the Owner's Manual and follow all Warnings and Safety Instructions. Failure to do so can result in serious injury. WARNING: Always Wear Eye Protection During Operation 424549 Rev. 1 10. 21. 08 SR Printed in the U. S. A. Safe Operation Practices for Walk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury. WARNING: Always Remove safety ignition key and disconnect spark plug wire and place it where it cannot contact plug in order to prevent accidental starting when setting up, transporting, adjusting or making repairs. [. . . ] Check controls to be sure they are functioning properly. LUBRICATION Keep your snow thrower well lubricated (See "LUBRICATION CHART"). Engine oil BELTS Check belts for deterioration and wear after every 50 hours of operation and replace if necessary. (See "TO REMOVE BELT COVER" in the Service and Adjustments section of this manual). The belts on your snow thrower are of special construction and should be replaced by original equipment manufacturer (OEM) belts available from your nearest dealer. Using other than OEM belts can cause personal injury or damage to the snow thrower. SNOW THROWER Always observe the safety rules when performing any maintenance. TIRES · Maintain proper air pressure in both tires (14­17 P . S. I. NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot 13 and corrosion. MAINTENANCE AUGER GEAR CASE · The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case. TRACTION DRIVE SYSTEM DO NOT lubricate the drive components inside the snow thrower. The sprockets, hex shafts, drive disc and friction wheel require no lubrication. The bearings and bushings are lifetime lubricated and require no maintenance. CAUTION: Any lubricating of the above components can cause contamination of the friction wheel and damage to the drive system of your snow thrower. Remove safety ignition key and disconnect spark plug wire from spark plug. Be sure to install klick pin into proper hole in wheel axle (See "TO REMOVE WHEELS" in the Service and Adjustments section of this manual). For approximate capacity see "PRODUCT SPECIFICATIONS" section of this manual. MUFFLER Inspect and replace corroded muffler as it could create a fire hazard and/or damage. SPARK PLUG Replace spark plug at the beginning of each season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in the "PRODUCT SPECIFICATIONS" section of this manual. ENGINE See engine manual. LUBRICATION Use only high quality detergent oil rated with API service classification SG­SL. Select the oil's SAE viscosity grade according to your expected operating temperature. CLEANING IMPORTANT: For best performance, keep snow thrower housing free of any dirt or trash. NOTE: Although multi-viscosity oils (5W30, 10W30 etc. ) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. [. . . ] 198563 169675 180684 73800600 19131316 198636 198638 73800400 DESCRIPTION POWER CORD RETAINER PIN WRENCH LOCKNUT 3/8-16 WASHER 3/8 SHEAR BOLT 1/4-20 X 1-3/4 SPACER LOCKNUT 1/4-20 2 1 6 8 7 01. 14. 004-A 1 KEY NO. 35062 DESCRIPTION SAFETY IGNITION KEY NOTE: All component dimensions given in U. S. 1 inch = 25. 4 mm IMPORTANT: Use only Original Equipment Manufacturer (O. E. M. ) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE POULAN 961980025




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual POULAN 961980025 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.