User manual RAYMARINE C-SERIES DISPLAY NEW FEATURES GUIDE

[. . . ] C-Series Display New Features Document number: 81298-1 Date: January 2007 C-Series New Features Trademarks and registered trademarks Autohelm, HSB, Raymarine, RayTech Navigator, Sail Pilot, SeaTalk and Sportpilot are registered trademarks of Raymarine Limited. Apelco is a registered trademark of Raymarine Holdings Limited (registered in all major marketing territories). AST, Autoadapt, Auto GST, Autoseastate, Autotrim, Bidata, Marine Intelligence, Maxiview, On Board, Raychart, Raynav, Raypilot, Raystar, ST40, ST60, Seaclutter, Smart Route, Tridata and Waypoint Navigation are trademarks of Raymarine Limited. All other product names are trademarks or registered trademarks of their respective owners. [. . . ] You can also choose to view the animation continuously or to step through it in increments of time you set. To view tide and current animations In the Chart application: 1. The Tide/Current Animation screen opens with animation paused. 4 C-Series Display New Features Direction and speed of current (green arrows) Tide height Press the ANIMATION PLAY/PAUSE softkey to start animation. Animation time and date are displayed on the status bar; the animation starts from the current time. Controlling the animation When you open the Tide/Current Animation screen, the toolbar provides softkeys to stop and start the animation; step the animation forwards or backwards in time; set the size of the step, or select a date for the animation. The animation plays in a loop: when it reaches the end of a 24-hour animation period, it starts again at the beginning. To start or stop the animation On the Tide/Current Animation screen: · Press the ANIMATION PLAY/PAUSE softkey. To view the animation in steps On the Tide/Current animation screen: · Press either the STEP BACK or STEP FWD softkeys. Chapter 2: Chart Application Updates 5 To set the step interval The Set Time Interval softkey gives you control over the Step Forward and Step Back functions. Use the rotary controller to adjust it (within the range of 15 to 120 minutes). Note: The animation must be paused for the Set Time Interval function to be available. To set the animation date 1. Table 2-1: Animation Date Toolbar Set the animation date to the current date. Opens the Edit Date pop-up screen: use the trackpad or rotary controller to enter the date you want to see an animation for. TODAY'S DATE PREV DATE NEXT DATE EDIT DATE 2. Press OK to save the new date and return to the Tide/Current Animation screen, which will update to display the tide or current for the date you chose. Note: Press CANCEL to ignore the date change and go back to the Tide/Current Animation screen, leaving the date setting unchanged. 2. 2 Range rings Range rings give you an incremental representation of distance from your vessel to help you judge distances at a glance. The rings are always centred on your vessel, and the scale varies to suit your current zoom setting. Each ring is labelled with the distance from your vessel. To turn range rings on or off In the Chart application: 1. Press the CHART LAYERS softkey. 6 C-Series Display New Features 3. Select RANGE RINGS ON/OFF. 2. 3 Navionics combined data cards Some Navionics data cards provide detailed bathymetric information in addition to standard chart information. You can choose between the standard chart view, or the view displaying bathymetric contours. To display bathymetric information In the Chart application: 1. If you select FISH and no data is available for your current position, the databar displays (FISH) to indicate that you are in that mode but without data. Chapter 3: Graphical Data 7 Chapter 3: Graphical Data The C-Series now gives you the option to display some navigation and engine data graphically. You can configure the unit to display a compass bar, and to show additional engine and genset (engine-driven electricity generator) data. 3. 1 Compass bar The compass bar gives you a continuous readout centred on your current heading or course over ground (COG). Arrows at either end of the bar indicate current steer direction. Active waypoint Bearing marker Steer direction · In heading mode, the bearing marker is RED. · When you use the compass bar with an active waypoint, the bearing marker is BLUE and the active waypoint symbol indicates the bearing to your waypoint. Turning the compass bar on and off You turn the compass bar on and off from the data toolbar. Table 3-1: ON COMPASS OFF DATABAR Softkey Options Displays the standard databar, at the top or side of the screen depending on your setup options. Replaces the standard databar with the compass bar, displayed along the top of the screen. Removes both the databar and the compass bar from your display. 8 C-Series Display New Features Note: When the compass bar is displayed the transducer icons remain visible in the top-right section of the screen. Compass bar setup The compass bar is set to open in heading mode. [. . . ] Use the rotary controller or trackpad to select the preset you want to move. Note: You can overwrite a channel that has already been assigned to a preset , but you will be prompted to confirm the action. 6. 7 Parental locking You can set up blocks on certain channels so that they can only be played if a correct password is entered. Parental locking must be enabled for the blocks on your selected channels to be effective. By default, blocking is not enabled. Chapter 6: Sirius Audio (US only) 37 To enable blocking On the Sirius Radio Control screen: 1. [. . . ]