User manual RAYMARINE C120 DISPLAY INSTALLATION GUIDE

[. . . ] C-Series Display Installation Manual Document Number: 87020-3 Date: March 2006 Trademarks and registered trademarks Autohelm, HSB, Raymarine, RayTech, RayTech Navigator, Sail Pilot, SeaTalk and Sportpilot are registered trademarks of Raymarine Limited. Apelco is a registered trademark of Raymarine Holdings Limited (Registered in all major marketing territories). AST, Autoadapt, Auto GST, Autoseastate, Autotrim, Bidata, Marine Intelligence, Maxiview, On Board, Raychart, Raynav, Raypilot, Raystar, ST40, ST60, Seaclutter, Smart Route, Tridata and Waypoint Navigation are trademarks of Raymarine Limited. All other product names are trademarks or registered trademarks of their respective owners. Copyright: ©Raymarine 2006 Important Information i Important Information Intended use This handbook provides information and instructions to assist in planning and installing your Raymarine C-Series Display, together with information that will be useful when you are connecting the C-Series Display to other equipment. [. . . ] Adjust the unit to the required angle for clear vision, and tighten the trunnion knobs. Flush mount Your display can be flush mounted on the console as follows: 1. A clear, flat area with suitable clearance behind the panel, is required. Fix the appropriate template - C70, C80 or C120, supplied in the document wallet, to the selected location, using masking or self-adhesive tape. Chapter 3: Installation 23 3. Using a suitable hole saw (the size is indicated on the template), make a pilot hole in each corner of the cut-out area. D6738_1 4. Ensure that the unit fits into the removed area and then file around the cut edge until smooth. Remove the mounting bracket knobs and the mounting bracket from the display unit. Drill four 4. 5 mm holes as indicated on the template to accept the securing bolts. Place the gasket onto the display unit and press firmly onto the flange. Connect the DC power cable, scanner cable, SeaTalk and Fishfinder connector cables to the display, avoiding tight bends. Slide the unit into the console and secure using the trim ring and suitable length bolts (see table below) 12. Locate the bezel over the front of the display (see page 24). 24 C-Series Displays Installation Manual Fixing bolts When console mounting your C-Series Display, avoid damaging the rear trim ring by using the correct length bolts. The length used is dependant upon bulkhead thickness: Bulkhead Thickness (mm) 0-3 3-7 7-11 11-15 15-19 19-23 Bolt length (mm) 12 16 20 24 28 32 Attaching the front bezel After you have installed the C-Series Display in the required position, you should attach the front bezel as follows: D6760-1 1. Carefully lift one edge of the screen protection film, so that it is accessible for removing when unit installation is complete. Chapter 3: Installation 25 2. Place the bezel over the front of the C-Series Display, ensuring that locking lugs located at the bottom edge of the bezel are latched into position. Ensure that the control buttons pass through their respective openings. Apply firm but even pressure to the bezel along the: · Outer edges - work from the sides upwards and then along the top edge, to ensure that it clips securely into position. · Inner edges - particularly along the chart card door edge, to ensure that the bezel sits flat. It is suggested that you use your thumb or forefinger in a circular motion to do this. Removing the front bezel To remove the front bezel: D7214_1 1. To prevent damaging your dash or placing undue strain on the trunnion bracket: · Trunnion mounted unit - unscrew and remove display from the mounting. Place a flat-bladed screwdriver in the aperture at the top right of the bezel and gently twist it to release the top clips. 26 C-Series Displays Installation Manual 3. Working from this corner, free the clips along the top edge of the display, then work towards the bottom edge. Taking care to ensure that the control buttons pass through the bezel. [. . . ] A symptom of incorrect timing is that bridges or piers shown on the picture appear to be bowed i. e. Own ship Own ship Own ship Timing early Timing late Normal D6625-2 To check the display timing: 1. On the radar picture locate a straight dock, seawall or bridge that is facing your boat. If the image is bent or bowed, the display timing will need adjustment Under certain circumstances, it may be easier to adjust the display timing with Main Bang Suppression (MBS) OFF. Note: MBS is reset to ON automatically when you finish adjusting the display timing. Chapter 5: Troubleshooting 45 Chapter 5: Troubleshooting Introduction This chapter provides information on troubleshooting your Raymarine C-Series Display at installation, and how to get assistance from Raymarine. 5. 1 How can I troubleshoot my Display? All Raymarine products are, prior to packing and shipping, subjected to comprehensive test and quality assurance programs. However, if you cannot successfully instal your Display unit, this section will help you to identify the most likely cause and show the corrective action required. [. . . ]