User manual RAYMARINE DSM30 INSTALLATION MANUAL

[. . . ] DSM300 & DSM30 Digital Sounder Module Installation Manual Document number: 87080-1 Date: November 2006 Trademarks and registered trademarks HSB, Raymarine and SeaTalk are registered trademarks of Raymarine plc. All other product names are trademarks or registered trademarks of their respective owners. Contents of this handbook ©Raymarine 2006 3 Contents Trademarks and registered trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Intended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · All cables should be adequately secured, protected from physical damage, and protected from exposure to heat. · Avoid running cables through bilges or doorways, or close to moving or hot objects. · Use a watertight feed-through wherever a cable passes through an exposed bulkhead or deckhead. Coil any extra cable and tie it out of the way. 1. 6 System Connections The connector panel provides the following connection sockets: · T/D, 7-pin socket for connecting to the transducer · HSB2, 4-pin socket for connecting to a C Series or hsb2 PLUS Series display · POWER, 3-pin socket; two for connecting to boat's DC power and one RF ground (screen) connection · SEATALK HS, RJ-45 socket for connecting to an E Series display C Series or hsb2 PLUS Transducer 10. 7 to 32 VDC (DSM300), 10. 7 to 18 VDC (DSM30) E Series Display D7464-2 CAUTION: To protect exposed pins, please place the attached dust cover over the socket (4-pin or RJ-45) to which you are not connecting a cable. Chapter 1: DSM Installation 15 Transducer Connection A 30 ft (10 m) cable is supplied with the transducer. This cable has a connector plug (with an outer nut that you must attach) at one end for attaching to the "T/D" connector on the sounder module. CAUTION: Do Not Cut or Splice the Transducer Cable · There is high voltage on the transducer cable. · Cutting the transducer cable severely reduces sonar performance. · Cutting the transducer cable will void the warranty and invalidate the European CE mark. DC Power Connection The DSM300 is intended for use on boat's DC power systems rated from 10. 7 V to 32 V. The DSM30 is intended for use on boat's DC power systems rated from 10. 7 V to 18 V (12 volt systems only). The power connection to the unit should be made at either the output of the battery isolator switch or at a DC power distribution panel. Power should be fed directly to the DSM via its own dedicated cable system and protected by a thermal circuit breaker or fuse on the red (positive) wire that is installed close to the power connection. This cable has a connector plug at one end for attaching to the "POWER" connector on the sounder module and 3 wires at the other end for connecting the power supply. The power cable may be extended by up to 60 ft (20 m) using a wire gauge of AWG 12 or greater. The RED wire must be connected to the feed from the positive (+) battery terminal and the BLACK wire to the feed from the negative (­) battery terminal. The shield wire (drain) should be connected to the boat's RF ground. CAUTION: If the power connections are accidentally reversed the system will not work. Use a multimeter to ensure that the input power leads are connected for correct polarity. DC power is connected at the 3-pin POWER connector on the unit's connector panel. The connector (viewed from the outside) and pin functions are shown in the following diagram and table. 16 DSM300 and DSM30 Installation Manual 1 2 D6162-1 3 Pin No. 1 2 3 Function Battery positive Battery negative Shield (drain wire) Color Red Black No insulation There is no power switch on the DSM. The unit turns on when the power cord is attached to boat's power and plugged into the POWER connector on the connector panel. Note: You should locate the DSM so that the power cord can be easily removed, if necessary. If the sounder is placed in a difficult-to-reach location, Raymarine strongly suggests installing an on/off switch on the DSM power cord at a point where it is easily accessible. Sounder Module Power Supply E Series Display Unit Transducer Power Connections with an E Series Display D9600-1 Chapter 1: DSM Installation 17 Sounder Module Power Supply C Series Display Unit Transducer Power Connections with a C Series Display Sounder Module Power Supply hsb 2 PLUS Series Display Unit Transducer Power Connections with an hsb2 PLUS Series Display D9602-1 D9601-1 18 DSM300 and DSM30 Installation Manual Ground Connection It is important that an effective RF ground is connected to the system. [. . . ] Table 2-2: Status LED Warning Indications Color W A R N I N G S 1 No of blinks 1 2 3 4 5 6 7 8 Meaning Transducer Sense Failure Network not detected 1 High Temperature Warning Reserved Reserved Reserved Reserved Watchdog Timeout Reboot Cleared every 10 min Amber After 30 seconds of no network activity, the sounder enters Standby mode: No sonar pings are emitted and no warnings are output on the LED. For example, if the Transducer Sense fails and the network is not detected, the LED blinks amber once, pauses 1. 5 secs, blinks amber twice 0. 5 secs apart, pauses 1. 5 secs, and then repeats the sequence until the problems are resolved or up to 10 minutes elapse. Chapter 2: Maintenance and Problem Solving 27 Table 2-3: Status LED Error Indications Color Red E R R O R S No of blinks 1 2 3 4 5 6 7 8 Meaning Unknown Error Battery Voltage Error High Temperature Error Flash Memory Failure Reserved Reserved Reserved Hardware Monitor Failure Cleared every 10 min A solid red LED (not blinking) indicates a fatal error condition. If the event of a fatal error, the system will power cycle to attempt to self-correct the condition. If the condition persists, please contact Raymarine Customer Service. 28 DSM300 and DSM30 Installation Manual 2. 4 How to Contact Raymarine On the Internet Visit the Raymarine World Wide Web site for the latest information on Raymarine electronic equipment and systems at: www. raymarine. com Customer Support Navigate to the Customer Support page for links to: · · · · · Finding Factory Service locations and Authorized Dealers near you Registering your Raymarine products Accessing handbooks in Adobe Acrobat format Downloading RayTech software updates Accessing the Raymarine solution database Clicking the Find Answers link routes you to our solution database. [. . . ]