User manual RAYMARINE RAYCHART 520 PLUS

[. . . ] hsb2 PLUS Series LCD Display Owner's Handbook Document number: 81186_3 Date: September 2002 Preface iii hsb2 PLUS Series LCD Display Owner's Handbook September 2002 INTENDED USE The display units detailed in this handbook may form part of navigational radar systems intended for light marine use. These displays and radar systems are only an aid to navigation. SAFETY NOTICES This radar equipment must be installed and operated in accordance with the instructions contained in this manual. Failure to do so can result in personal injury and/or navigational inaccuracies. Adjustments require specialized service procedures and tools only available to qualified service technicians ­ there are no user serviceable parts or adjustments. [. . . ] The waypoint is placed at the current vessel position, or if not available, the cursor position. WAYPOINT LIST MAKE NEW WAYPOINT Placing a Waypoint 5-10 hsb2 PLUS Series LCD Display WAYPOINT LIST SYMBOL NAME WAYPOINT 001 WAYPOINT 002 WAYPOINT 003 WAYPOINT 004 WAYPOINT 005 POSITION BRG _186° TEMP 50°21^966N 001°20^368W RNG _21. 0nm DEPTH TIME ---°C --/--/-- ---m --:--:-- Placing a Waypoint DATE GOTO WAYPOINT EDIT WAYPOINT MAKE NEW WAYPOINT WAYPOINT TRANSFER D4262-2 3. You can use the soft keys to edit the waypoint position as described in Editing the Waypoint Details on page 5-13. It is added to the Waypoint List and named with the next available number. To return to the default soft key display, press ENTER or CLEAR twice. Press MARK, followed by the WAYPOINT LIST soft key; the Waypoint List and associated soft keys are displayed. Press the MAKE NEW WAYPOINT, the waypoint is placed at the current vessel position, or if not available, the cursor position. To change the position press the LORAN TDs soft key; the WPT POSITION (LORAN TDs) screen is displayed, with it's associated soft key. Note: You can enter waypoints as Loran TDs which are converted to Lat/Long coordinates. However, although the waypoint is shown in both Lat/Long and Loran TDs in the Waypoint List, you can subsequently only edit the position as Lat/Long coordinates. TD entries in the Waypoint List are shown only for those waypoints which were entered as TDs. Chapter 5: Standard Chart Operations 5-11 WPT POSITION (LORAN TDs) CHAIN SLAVES TD 1 TD 2 ASF 1 ASF 2 6731 - NELS Lessay Y - Z (24 -39) 29138. 0 44713. 8 +0. 0 +0. 0 CHAIN ASF1/ASF2 SET TD 1 SET TD 2 D5591-1 i. The CHAIN soft key, which enables selection of both the Chain and it's Slave: WPT POSITION (LORAN TDs) CHAIN SLAVES TD 1 TD 2 ASF 1 ASF 2 6731 - NELS Lessay Y - Z (24 -39) 29138. 0 44713. 8 +0. 0 +0. 0 SELECT CHAIN SELECT SLAVES D5592-1 ii. The ASF1/ASF2 soft key, which presents two soft keys for editing ASF 1 and ASF 2 parameters independently: SET ASF 1 SET ASF 2 D5593-1 iii. The SET TD 1 and SET TD 2 soft keys, which enable editing of each TD's parameters independently. Note: Except for the CHAIN setting, parameters are edited using the trackpad as described in Editing the Waypoint Details on page 5-13. When editing is complete, press the ENTER key to save the waypoint or CLEAR to cancel the operation; the display returns to the New Waypoint screen. Press the ENTER or CLEAR to return to the Waypoint List. Placing a Waypoint 3. Edit the Loran parameters as required, using: 5-12 hsb2 PLUS Series LCD Display Selecting a Waypoint Positioning the cursor over a waypoint selects that waypoint and accesses the waypoint soft keys. These keys enable you to GOTO (described in Section 5. 5), EDIT (symbol, name, position), ERASE or MOVE the waypoint. Selecting a waypoint from the List allows you to GOTO and EDIT (symbol, name, position, erase) the waypoint. The Waypoint List also provides options to make a new waypoint and transfer waypoints. Move the cursor over the waypoint, until the letters WPT are displayed. The Waypoint Data box (see Waypoint Data Display on page 5-12) and the following soft keys are displayed: GOTO WAYPOINT EDIT WAYPOINT ERASE WAYPOINT MOVE WAYPOINT D4163-1 WPT Selecting a Waypoint MARKS The selected waypoint can be edited via these soft keys. [. . . ] The Installed Warranty provides for onboard repair or exchange, by Raymarine or it's approved service agents, for a period of 2 years/24 months, from date of sale of the boat to the end user ­ where the equipment has been installed by a Raymarine certified installer, or from commissioning of the installation by a Raymarine certified installer, or 30 months from date of shipment of the equipment from Raymarine ­ whichever expires first, except as provided below. Obtaining Warranty Service In the event of Warranty service being required, contact Raymarine or the nearest Raymarine certified service agent ­ a full list of local service agents are available on the Internet or can be requested from the nearest Raymarine agent. A suitable proof of purchase, showing date, place of purchase, and serial number must be made available to Raymarine or authorized service agent at the time of request for Warranty service. In cases where a Raymarine certified installer has not installed the product; i. e. Limited Warranty, the affected unit must be returned to the local Raymarine approved service agent, with a copy of proof of purchase and/or completed warranty card. [. . . ]