User manual RAYMARINE RAYSTAR 120 GPS

[. . . ] Raystar 120 & Raystar 112LP GPS Receivers Owner's Handbook Document Number: 81203-1 Date: January 2002 Handbook information To the best of our knowledge, the information in this handbook was correct when it went to press. However, Raymarine cannot accept liability for any inaccuracies or omissions it may contain. In addition, our policy of continuous product improvement may change specifications without notice. As a result, Raymarine cannot accept liability for any differences between the product and the handbook. Copyright Information Autohelm®, Raymarine® and SeaTalk® are registered trademarks of Raymarine Ltd. [. . . ] In a location that is open and clear of any obstructions (such as masts, search lights, or other structures) that could block line-of-sight reception of signals. As low as possible: the height of the receiver is not as important as it having a clear view horizon to horizon for optimum signal reception. In fact, the lower the unit can be mounted and have a clear view to satellites, the better. The more stable the unit, the more effectively it will track satellites low to the horizon. · 2 Installation Note: Do NOT mount the receiver up a mast, as the receiver will swing with the boat, leading to significant COG/SOG errors. · As far as possible from any sources of interference: the receiver should be separated by at least 1 m (3 ft) from other antennas and electronic equipment. It should not be mounted in the direct path of a radar's beam. Mounting options You can mount the Raystar 120/112LP on a pole or flush on a suitable horizontal surface. When mounting the receiver flush to a surface: · · select a suitable area which allows access to the underside of the mounting surface for fixing avoid areas where the receiver might be trodden upon or where it might present a tripping hazard Cabling route When planning the location for the unit, consider the best route for running the cable between the receiver and GPS display unit or to the rest of an integrated system. Ideally, you should try to route the cable so it is: · · hidden from view separated as far as possible from other cables (to prevent interference) Chapter 2: Installation 9 2. 3 Mounting the receiver When you have selected a suitable location, follow the relevant installation instructions for Pole mounting or Surface mounting. Pole mounting Note: You will need to obtain a suitable pole with 1 inch 14 TPI thread. Securely attach the pole mount base to a suitable pole or rail mount bracket. Pass the cable through either: A: the center hole of the pole mount base, or B: the cable exit hole alongside the center hole, or C: the side exit channel Note: If you intend to use the side exit channel, remove the two plastic tabs obstructing the channel. If you do not remove these tabs before using the cable channel, you could damage the cable. Check the cable is positioned correctly, then secure the receiver to the pole mount base using the two screws provided. . 2 Installation C B A D5898-1 Figure 2-1: Pole mounting 10 Raystar 120 & Raystar 112LP GPS Receivers - Owner's Handbook Surface mounting 1. Use the template supplied in this handbook to mark the two 6 mm (0. 25 in) fixing holes. OPTION A: If the cable is going to pass through the mounting surface drill either: · 6 mm (0. 25 in) center hole (for bare-ended SeaTalk cables), or · 19 mm (0. 75 in) center hole (for NMEA plugged cables) OPTION B: If the cable is going to exit from the side of the receiver above the mounting surface, remove the two plastic tabs (1) obstructing the cable channel. If you do not remove these tabs before using the cable channel, you could damage the cable. Stick the supplied gasket (3) to the mounting surface, ensuring that the holes on the gasket correspond with the drilled holes 5. Pass the cable down through the center hole (Option A) or route it through the cable exit channel (Option B). Carefully position the receiver so the mounting studs pass through the holes in the mounting surface. Secure the receiver to the surface using the two thumb nuts (4). A B 1 2 Installation 2 3 2 3 4 4 Top view Underside view D5897-1 Figure 2-2: Surface mounting Chapter 3: NMEA/SeaTalk Connections 11 Chapter 3: NMEA/SeaTalk Connections The sections in this chapter explain how to connect the NMEA and SeaTalk versions of the Raystar 120/112LP to other equipment: Section Section 3. 1, Raystar 120/112LP - NMEA versions Section 3. 2, Raystar 120/112LP - SeaTalk versions Section 3. 3, Using a connector block Page 11 12 13 3. 1 Raystar 120/112LP - NMEA versions Note: As with all on-board marine equipment, you must ensure that the power supply connection to the Raystar 120/112LP is adequately protected by a suitably rated fuse or circuit breaker. Usually this will be achieved by providing power via a fused display unit. Using the moulded 6-pin NMEA connector 3 NMEA/SeaTalk Connections The unit is normally connected to an NMEA system via the 10 m (33 ft) cable terminated with a moulded 6-pin connector (see Figure 3-1). Use this connector if your equipment has a compatible GPS port. NMEA connector 3 Screen (0 V/ground) 2 Screen (0 V/ground) 4 Yellow (NMEA out) 1 Red (Power ) 6 Brown (RTCM in) 5 Green (NMEA in) D5899-1 Figure 3-1: NMEA connector pin-outs 12 Raystar 120 & Raystar 112LP GPS Receivers - Owner's Handbook Using an alternative NMEA connector If your equipment is not compatible with the supplied connector, remove it and then either: · · use a connector block to re-connect the cable connect the cable to another type of NMEA connector. Refer to Table 3-1 for information about cable colors. The cable can be cut as necessary to the required length, or coiled and stored out of the way. [. . . ] The rights and obligations of each party to this Agreement shall not be governed by the provisions of the United Nations Convention on Contracts for the International Sale of Goods. If any action at law or in equity, including an action for declaratory relief or injunctive relief is brought to enforce or interpret the provisions of this Agreement, the prevailing party shall be entitled to reasonable attorneys' fees in addition to any other relief to which the party may be entitled. Any waiver by either party of any default or breach hereunder shall not constitute a waiver of any provision of this Agreement or of any subsequent default or breach of the same or a different kind. Limited Warranty Certificate Raymarine warrants each new Light Marine/Dealer Distributor Product to be of good materials and workmanship, and will repair or exchange any parts proven to be defective in material and workmanship under normal use for a period of 2 years/24 months from date of sale to end user, except as provided below. Defects will be corrected by Raymarine or an authorized Raymarine dealer. [. . . ]